SWR Sound 2X10C Extension Speaker Output Jacks, Speaker Fuse, Internal Speaker Mode Switch

Page 13

NOTE: The frequency response of the Workingman's 2x10C is far greater than usually found in musical instrument amplifiers (20 Hz to 40K Hz). This was engineered in order to give the bass player the same punch and clarity on stage as found in the studio or concert P.A. systems. Therefore, it is doubly important that you are aware of the impedance and power rating of the extension speak- ers that you intend to use, and that they are compatible with the Workingman's 2x10C. Speakers that have been overdriven are easy to detect and generally do not fall under a manufacturer's warranty.

EXTENSION SPEAKER OUTPUT JACKS

One 1/4" phone jack is provided for connection of an extension speaker to the Workingman's 2x10C. Only SPEAKER CABLE of 18 gauge or heavier (the heavier the cable, the lower the gauge) should be used to connect an extension speaker to your Workingman's 2x10C. Do not use shielded instrument cable in this application, as this can result in intermittent power loss, cause your amp to oscil- late and damage itself and/or your speakers, and render the cable useless for any purpose.

Recommended SWR Speaker enclosures for use as an extension cabinet with the Workingman's 2x10C include:

Workingman's 2x10T

Workingman's 1x15T

Workingman's 4x10T

Big Ben (1x18 sub)

SPEAKER FUSE

The speaker fuse is provided to protect your speakers in the unlikely event of a power amp failure or to protect your power amplifier from incorrect speaker impedances or hookups. Size and rating of the fuse is 3AG, 10 amp, fast-blo. Do not defeat the purpose of this feature by using a higher rated fuse as it can damage your amplifier and void your warranty.

The fuse can open as a result of a fault in the speaker cable, the speakers themselves, or the power amp being sent well into clip- ping. With this in mind, it is wise to carry extra fuses at all times.

INTERNAL SPEAKER MODE SWITCH

Located on the small panel on the rear of the Workingman's 2x10C's speaker cabinet, this two-position switch controls the signal sent from the power amplifier to the internal speaker cabinet only. When set to the On (top) position (default setting from the factory), the Workingman's 2x10C will operate normally and the sound of your amplified bass will be heard from the internal speaker cabinet. When set to the Off (bottom) position, the internal cabinet's signal will be defeated, but any extension speaker connected will still be audible. This could be extremely useful if you wish to use the amplifier in your 2x10C in a head-only configuration, at which point you could connect any speaker cabinets to the amplifier just so long as the resulting total impedance was no lower than 4 ohms. This can also be useful for silent practicing (in conjunction with the Headphones Jack, listed previously), or for defeating the audio while you re- patch cables or plug and unplug your instrument. This switch will not affect the signal present at the various audio outputs (XLR Out, Effects Send, Tuner Out).

In some ways, this switch is similar to the Speakers On/Off Switch on the front panel, but remember: the Speakers On/Off Switch on the front panel will defeat all speakers connected to the amplifier, while the Internal Speaker On/Off Switch will only defeat the inter- nal speaker system. But since either one can defeat the internal speaker system, they can override each other when set to the bot- tom position. Make sure that both switches are in the "On" position if you want to hear sound from your internal speaker system.

NOTE: One last time − if the volume on your instrument is up, and your Gain and Master Volume controls are up, and especially if you're seeing the Preamp Clip and Limiter Active LED's illuminate while you're playing…and you can't understand why you're not get- ting any audible output from the Workingman's 2x10C, check the position of this switch!

WORKINGMAN’S 2X10C • 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Workingman’s 2X10C Introduction Specifications Workingmans 2X10C Front Panel FeaturesWorkingmans 2X10C Getting Started Cabinet Construction and FeaturesTuner OUT Balanced D.I. XLR OutputInput Jacks PASSIVE/ACTIVE Input JackPreamp Clip LED Gain ControlAural Enhancer Workingmans 2X10C 5-BAND Graphic EQ Section Using the 5-BAND Graphic EQ Section Bass ControlOverview Midrange ControlsVariable Limiter Control with defeat option Effects Blend ControlDefeating the Limiter Circuit Limiter Active LEDSpeakers ON/OFF Switch Master Volume ControlHeadphones Jack stereo only Power ON/OFF SwitchEffects Send Effects Loop for outboard effects devicesEffects Receive HOW Impedance Affects Power Ratings Combo Cabinet JACK/PLUG AssemblyWorkingmans 2X10C Power Amplifier Minimum Impedance Ratings Extension Speaker Output SectionYour rig Workingmans 2X10C Power Delivery Capabilities Power RatingsExtension Speaker Output Jacks Internal Speaker Mode SwitchSpeaker Fuse Tweeter Mode Switch Workingmans 2X10C Suggested SettingsLine Fuse A/C or Mains Fuse Cord ReceptacleWORKINGMAN’S 2X10C WORKINGMAN’S 2X10C Limited Warranty

2X10C specifications

The SWR Sound 2X10C is a powerful and versatile bass cabinet designed for both studio sessions and live performances. With its compact size and lightweight design, it is an ideal choice for musicians seeking portability without sacrificing sound quality. The cabinet features two 10-inch custom-designed speakers, specifically engineered to deliver a balanced tonal range and impressive low-end response.

One of the standout features of the 2X10C is its high power handling capability, allowing it to handle up to 400 watts RMS. This ensures that even when pushed to its limits, the cabinet maintains clarity and punch, crucial for any live show or recording environment. The cabinet is also equipped with a high-efficiency horn tweeter, which enhances the higher frequencies and provides a sparkling top-end that complements the rich tones produced by the 10-inch woofers.

The cabinet utilizes SWR's proprietary technologies to enhance performance. The "Bass Reflex" design features strategically positioned ports that help to eliminate unwanted air turbulence while maximizing low-frequency response. This design not only promotes deeper bass tones but also allows the cabinet to remain lightweight, making it easier for musicians to transport.

Another key characteristic of the SWR 2X10C is its rugged construction. Built from durable materials, the cabinet is designed to withstand the rigors of both touring and frequent use. Reinforced corners and a heavy-duty grille protect the speakers from potential damage, ensuring the longevity of the cabinet.

For connectivity, the 2X10C comes with dual 1/4-inch input jacks, enabling easy integration with various amplifiers and allowing for daisy-chaining additional cabinets if more sound output is required. The cabinet is compact enough to fit into most environments, making it a versatile option for a range of musical genres.

In summary, the SWR Sound 2X10C combines advanced features, innovative technology, and robust build quality, making it an exceptional choice for bass players looking for a reliable cabinet that delivers impressive sound across various settings. Whether in a rehearsal space, a studio, or on stage, the 2X10C stands out as a top-tier option that meets the demands of modern musicians.
Top Page Image Contents