Ball Float Vacuum SHUT-OFF | Nilfisk-ALTO MX 521 H manual

7Allow the heat exchanger two minutes to reach operating temperature. The red light (1) will go out when the heater has reached maximum operating temperature. The light will be ON most of the time while you are cleaning.

8Turn the pump ON (4) and set the pressure selection switch (3) to the desired spraying pressure: Carpet at 300 PSI or Upholstery at 50 PSI.

9Turn the vacuum ON (2). The motor will start slowly. This will increase the life of the motor and prevent a large current surge from tripping the circuit breaker in the wall.

10Begin cleaning using the correct hoses and tool.

11Use defoamer in the recovery tank any time foaming occurs.

12Monitor the water level in the solution tank. Do not let the pump run dry.

13When the solution tank gets low, turn the pump and the vacuum off (3 & 4), fill the solution tank, empty and clean the recovery tank.

14When finished with the job, remove any unused solution from the solution tank by vacuuming it into the recovery tank. Run a few gallons of clean water through the system.

15Drain the recovery tank by placing the dump hose over a drain, or into a bucket, and remove the hose cap.

16Disconnect the hoses from the cleaning tool, and reel the hoses up onto the hose spool.

NOTE: to remove the reel, with the hoses, from the machine, pull the vacuum hose loose from the hose barb on the front of the tank. Disconnect the solution hose quick coupling. Push the vacuum hose into the center of the spool. Grasp the spool on both sides, and lift it off the machine. NOTE: before servicing any component in the base cabinet, the hoses and spool must be removed from the machine before the tanks can be lifted open.

CAUTION: if foam or water comes out the vacuum exhaust, turn the machine off immediately

CAUTION: to avoid vacuum motor damage, always use a defoamer any time foam is present.

BALL FLOAT VACUUM SHUT-OFF:

Prior to using the machine, always check that the float filter is clean and the ball can travel freely. When the recovery tank is full, the ball float will rise and will shut off the vacuum flow to prevent any more water from entering the tank. Turn off the vacuums, and empty the recovery tank.

NOTE: if foam is present, or if the ball float is prevented from rising, the float will not be able to stop the air flow, and the tank may over fill. Water damage to the vacuum motors is not covered by warranty.

11-600205211REVA

MX 521 H specifications

The Nilfisk-ALTO MX 521 H is a high-performance industrial vacuum cleaner designed to tackle challenging cleaning tasks across a variety of sectors. Renowned for its robust construction and exceptional suction capabilities, the MX 521 H is a perfect solution for both coarse and fine debris collection, making it indispensable for factories, workshops, and construction sites.

One of the standout features of the MX 521 H is its powerful 2.2 kW motor, which delivers a consistent airflow and ensures efficient dust removal. This industrial vacuum cleaner has a capacity of 50 liters, allowing users to complete large cleaning jobs without frequently stopping to empty the tank. The durable plastic construction further enhances the machine's lifespan, while its design allows for easy handling and mobility, thanks to its integrated wheels.

The MX 521 H boasts advanced filtration technologies that enhance its cleaning efficiency. It comes equipped with a HEPA filter, which effectively captures tiny particles and allergens, ensuring cleaner air in the working environment. This feature is particularly advantageous for sensitive areas like hospitals and laboratories where air quality is critical. Additionally, the vacuum is fitted with a dust bag that is easy to replace, facilitating quick maintenance.

Ergonomics play a vital role in the MX 521 H's design. The control panel is intuitively positioned for easy access during operation, while the ergonomic handle provides comfort even during extended use. The vacuum is also designed with a low profile, enabling it to access hard-to-reach areas, enhancing its versatility on the job site.

Another key characteristic of the Nilfisk-ALTO MX 521 H is its versatility. It excels in both wet and dry applications, allowing operators to switch between different cleaning tasks effortlessly. This feature is particularly useful in environments where spills or wet debris are common, ensuring that the vacuum can handle a variety of situations without the need for additional equipment.

In summary, the Nilfisk-ALTO MX 521 H is an industrial vacuum cleaner that combines power, efficiency, and ease of use. With its robust motor, high-capacity tank, advanced filtration technology, and ergonomic design, it is expertly suited for demanding industrial cleaning applications. The MX 521 H stands out as an excellent investment for any business seeking effective cleaning solutions in challenging environments.