Desa SDVBPD, SDVBND installation manual Manual Lighting, Optional HAND-HELD Remote Operation

Page 27

OPERATING STOVE AND BURNER SYSTEM

Manual Lighting Procedure Optional Hand-Held Remote Operation

27

OPERATING STOVE WITH BURNER SYSTEM

Continued

MANUAL LIGHTING

procedure

1.Remove glass door (see Removing/Replacing Glass Door, page 24).

2.Follow steps 1 through 8 under Lighting Instructions, page 26.

3.Depress gas control knob and light pilot with match.

4.Keep gas control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release gas control knob. Now follow steps 10 through 14 under Lighting Instructions, page 26.

5.Replace glass door (see Removing/Replacing Glass Door, page 24).

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, page 38). Follow instructions included with the remote control.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions on page 26.

1.After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position (see Figure 60). Note: The burner may light if hand-held remote was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch in the RE- MOTE or ON position when the pilot is not lit. This will drain the battery.

Selector Switch in Remote

Gas Control Knob

Variable

Position (Optional Remote

in On Position

Control Knob

Control)

 

 

 

LO

 

IN OUT

Figure 60 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

ON/OFF SERIES (MODELS GHRCB AND CGHRCB)

Hold the control button on the hand-held remote until burner turns on. Hold the control button again until burner turns off (see Figure 61).

To Lock press both buttons on hand-held remote control until light stops flashing. Hand-held remote control is now locked. If the fire is on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed.

To Unlock press both buttons together on hand-held remote control untilthelightstopsflashing.Thehand-heldremoteisnowunlocked.

Control Button

Turns Burners

On and Off

Figure 61 - On/Off Hand-Held Remote Control Unit (C)GHRCB

THERMOSTAT SERIES (MODELS GHRCTB AND CGHRCTB)

Thehand-heldremotecanbeoperatedusingeitherthemanualmode (MANU) or thermostatic mode (AUTO) (see Figure 62). To select Fahrenheit/Centigrademodedisplay,carefullypressthe˚C/˚Fmode button with the end of a paper clip or similar blunt object.

Manual Mode

1.Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2.Press the MANU button to turn on the fireplace.

3.Press the POWER and LOCK buttons together to turn off the fireplace.

Auto (Thermostatic) Mode

1.Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2.Press AUTO button to select this mode.

3.Set the desired room temperature by pressing the TEMP + or - buttons.

4.Press the POWER and LOCK buttons together to turn off the fireplace

Note: Do not leave the hand-held remote in the AUTO mode close to the fireplace. The radiant heat from the fireplace will turn off the fireplace. Ideally, place the hand-held remote in the center of the room facing towards the fireplace.

Note: Do not hold the hand-held remote for a long time. Body temperature will affect its operation in the AUTO mode.

Digital Display

Turns Hand-Held

Remote On or Off and

Shows

Allows You to Choose

Temperature and

the Manual Setting

Settings

 

Turns Burners

Selects Auto Setting

 

On or Off

Increases Room

 

Decreases Room

Temperature in

AUTO Mode

Temperature in

 

AUTO Mode

Locks System to

 

 

Prevent Accidental

 

Ignition

Figure 62 - Thermostat Hand-Held Remote Control Unit (C)GHRCTB

For morevisit www..com

112126-01B

Page 26 Page 28
Image 27
Page 26 Page 28
Contents VH series Stove OWNER’S Operation and Installation ManualFor Your Safety For Your Safety What to do if YOU Smell GASSafety Information Table of ContentsWith stove Product IdentificationPRE-INSTALLATION Preparation Product Features Local CodesGlossary of Terms PRE-INSTALLATION Preparation Cast Iron Stove and DIRECT-VENT Burner System AssemblyStove Body Assembly Locating Threaded Holes for Legs and Door Attachment Amity Models Installing DIRECT-VENT Burner System Into Stove BodyRemoving Front Surround Panel Removing Screen OptionalTOP View Installing Optional Blower Accessory Installing the BlowerBlower Wiring Layout Thermostat Blower Shown Installing Rear CoverLocation of Vent Termination General VentingGeneral Venting Venting Installation Installation PrecautionsInstallation Planning Installing Vent System in a Chase Installation for Horizontal TerminationVent Opening Requirements Venting with Two 90 Elbows Horizontal Termination ConfigurationsHorizontal Venting Venting with Three 90 ElbowsFlat Ceiling Installation Installation for Vertical TerminationCathedral Ceiling Installation Vertical Termination ConfigurationsVenting with Two 90 Elbow Venting with Two Elbows Vertical Venting Configuration Using Two 90ElbowsNumber Description High Altitude InstallationParts Lists for Venting Kits and Components Vertical VentingCheck GAS Type Stove and DIRECT-VENT Burner System InstallationInstalling GAS Piping to STOVE/ Burner System Location Installation Items NeededConnecting STOVE/BURNER System to GAS Supply Pressure Testing Gas Supply Piping SystemChecking GAS Connections Pressure Testing Burner System Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Remote Receiver and 9-volt Alkaline Battery Installing Optional Wall Mounted Thermostat GWMT1REMOVING/REPLACING Glass Door Installing Remote ReceiverInstalling Log No Installing Log No Installing LOGS, Lava Rock and Glowing EmbersTo Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Stove with Burner System Lighting InstructionsThermostat Series Models Ghrctb and Cghrctb Manual LightingOptional HAND-HELD Remote Operation ON/OFF Series Models Ghrcb and CghrcbOperating Optional GWMT1 Wall Mounted Thermostat Operating Optional Blower AccessoryPilot Assembly Inspecting BurnersLogs Cleaning and MaintenanceGlass Door Pilot and BurnersObserved Problem Possible Cause Remedy TroubleshootingOrifice Above Gas leak. See Warning statementParts Under Warranty SpecificationsWiring Diagram Replacement PartsModels Sdvbnd Sdvbpd Illustrated Parts BreakdownModels SDVBND, Sdvbpd Parts ListVictor Hearth Stove Body Indicates Color Suffix Designation Oxford Amity Stove BodyDescription QTY Indicates Color Suffix DesignationTechnical Service Service HintsAccessories Owners Registration Form For Com 112126-01B Warranty Information
Related manuals
Manual 42 pages 10.67 Kb

SDVBPD, SDVBND specifications

Desa SDVBPD and SDVBND are pioneering advancements in the domain of digital communication, designed to optimize services, enhance user engagement, and streamline processes in various sectors, including education, healthcare, and local governance. These systems have emerged as essential tools for efficient information dissemination and resource management.

One of the main features of Desa SDVBPD is its focus on decentralized communication. By utilizing local infrastructure, this system empowers communities to share information effectively and enhance interactions among residents. It enables local authorities to communicate directly with citizens, ensuring that pertinent information reaches the intended audience promptly. This feature is especially vital in emergency situations, where timely updates can significantly impact community safety and preparedness.

Similarly, SDVBND offers a robust platform for managing digital transactions and records. Its integration of blockchain technology ensures that all data processed is secure, immutable, and transparent. This characteristic is particularly beneficial for local government operations, as it minimizes the risk of fraud and enhances accountability in public service delivery. By leveraging this technology, Desa SDVBND can facilitate smooth and fast transactions between citizens and government entities, thereby transforming the way public services are accessed.

Another remarkable aspect of both systems is their accessibility. Designed with user-friendly interfaces, these platforms cater to individuals of varying technological proficiencies. Mobile compatibility allows users to engage with the systems from smartphones and tablets, making it easier to stay informed and involved. Furthermore, the platforms are multilingual, ensuring that communication is inclusive, reaching diverse populations within communities.

Interoperability stands out as a significant characteristic of Desa SDVBPD and SDVBND. Both systems are designed to seamlessly integrate with existing infrastructure and technologies, such as cloud computing and artificial intelligence. This adaptability enhances their functionality, enabling real-time data analysis and improved decision-making.

In conclusion, Desa SDVBPD and SDVBND represent a significant leap forward in community engagement and service delivery. By leveraging decentralized communication, blockchain technology, accessibility, and interoperability, these systems not only improve operational efficiency but also foster a sense of community empowerment. As they continue to evolve, they hold great promise for enabling smarter, more connected communities that can thrive in an increasingly digital world.
Top Page Image Contents