Zanussi ZDF490 manual Installation Instructions, Things YOU Need to Know, Things to Note

Page 7

INSTALLATION INSTRUCTIONS

THINGS YOU NEED TO KNOW

WARNINGS

￿This appliance must be installed by a qualified electrician/competent person. Safety may be impaired if installation is not carried out in accordance with these instructions.

￿This appliance must be earthed.

￿Do not remove the screws from the earth tab extending from the oven mains terminal block (Fig. 6).

￿Before connecting the appliance make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This is situated on the lower front frame of the appliance and can be seen upon opening the top cavity door. Alternatively the rating plate may also be found on the back or top of some models (where applicable).

￿Do not alter the electrical circuitry of this appliance.

THINGS TO NOTE

￿This appliance is designed to be fitted in cabinets of the recommended dimensions as shown (Fig. 2).

￿If your cabinet interior dimension is between 565-570mm the oven may still be fitted. However a minor modification to the cabinet will be required to reduce the aperture size down to 560-565mm. To allow the product to be securely screwed into the cabinet.

￿The dimensions given provide adequate air circulation around the unit within the cabinet, ensuring compliance with BS EN60-335.

￿Enquiries regarding the installation of the cooker point, if required, should be made to your Regional Electricity Company to ensure compliance with their regulations.

￿The cooker socket switch should be outside the cabinet but within 2m of the appliance to make it accessible to switch off the appliance in case of an emergency.

￿To protect the hands, wear gloves when lifting the oven into its housing.

NOTE: HOUSE CIRCUIT

Earth leakage and continuity tests must be carried out before the appliance is connected to the mains supply and re-checked after fitting.

GETTING THINGS READY

CHOICE OF ELECTRICAL CONNECTION

￿There are three possible ways to connect your appliance. In each case the appliance should be operated using at least 6mm2 twin core and earth PVC insulated multicore cable. Please choose from the most appropriate after reading the different methods:-

a)By connecting the appliance to a cooker point (having a double pole isolating switch with at least 3mm contact separation in all poles and neutral) and protected with a fuse or miniature circuit breaker at your mains fuse box.

Subject to Regional Electricity Companies regulations if you wish to connect the oven and hob to the power supply you may use one of the following two methods:-

b)By connecting the appliance together with a hob directly to a cooker point(s). Having a double pole isolating switch with at least 3mm contact separation in all poles and neutral.

c)If you wish to connect an oven and a hob to a cooker point you can by connecting the oven and hob separately to the cooker point. Oven and hob units should be separately connected to a cooker point. See Fig. 1.

Fig. 1

NOTE: It is good practice to :

￿Fit an Earth Leakage Circuit Breaker to your house wiring.

￿Wire your appliance to the latest IEE regulations.

PREPARING CABINET FOR FITTING OF OVEN

￿Make sure that the cabinet is the correct size for the appliance to be fitted (Ref. Fig. 2).

￿If the cabinet is between 565-570mm, then the cabinet should be modified so that at the screw fixing points the recommended dimension of at

least 560-565mm is maintained. The modification should ideally be localised to ensure that after screw fitment the oven is securely fixed into position.

￿The cabinet must be stable and level securing it to the wall or floor. If necessary, make arrangements to ensure the shelf upon which the oven will rest is level.

￿When the appliance is installed ensure a minimum gap of 2mm is maintained between the trim on the bottom edge of the appliance, and any corresponding door / panel.

7

Image 7
Contents BUILT-IN Electric Double Oven Technical Details Model NO. ZDF Contents Contents During Operation SafetyGeneral After USEGetting Things Ready Installation InstructionsThings YOU Need to Know Things to NoteBuilt In Installation Recommended Cabinet Dimensions in MillimetresPreparing Cable HOW to Finish UnpackingTools Required Making the Electrical ConnectionsConnecting to a HOB or Cooker Point Connecting to Mains TerminalChecking Electrical Connections Fitting Into the Cabinet Getting to Know Your Appliance IntroductionCDE F About Condensation and Steam General Notes on Using the OvensControl Panel Indicator Neons Rating PlateGrill and Oven Furniture HOW to SET the Countdown Oven TimerSET the Time of DAY Setting the Oven Timer Control To Cancel the CountdownTo SET the Timer to Switch on and OFF Automatically To Cancel AN Automatic Programme To SET the Timer to Switch OFF onlyTo Return the Appliance to Manual Automatic Cooking Uses of the Grill Selecting the Grill GrillGrill PAN and Handle Hints and Tips Grilling ChartUses of the TOP Oven TOP OvenSelecting the TOP Oven To FIT the TOP Oven Shelf To FIT the Main Oven Shelves Main FAN OvenUses of the FAN Oven Selecting the FAN OvenHints and Tips Oven Cooking Chart Roasting Chart Roasting ChartDefrosting Uses of Defrost FeatureSelecting Defrost Cleaning the TOP Oven Roof Care and CleaningCleaning the Outside of the Appliance Cleaning Inside the TOP and Main Oven CompartmentCleaning Between the Outer and Inner Door Glass To Remove the Wirework RunersTo Remove the Outer Glass Replacing AN Oven Light Bulb To Replace the Outer GlassSomething not WORKING? Grill, oven and timer do not workService and Spare Parts Standard guarantee conditions Guarantee ConditionsPage Page Important Notice