Maintenance, Operation tips and tricks

Never use a cheater pipe extension on the hydraulic pump handle. Failure to comply may result in personal injury.

7.Make sure the release valve is closed, then use the pump handle bar (Figure 7) to advance the die and bend the pipe.

Pump

Handle

Bar

Release Valve

Figure 7. Operating pump and release valve.

8.When you are finished with your bend, release the pressure by opening the release valve and the ram will automatically retreat.

Operation tips and tricks:

•If the ram reaches the end of its stroke but still has not completed a desired bend, release pressure just enough to remove the pipe. Set the rollers either one or two holes farther in to finish the bend.

•We recommend making templates of accu- rate 45˚ and 90˚ angles. Compare these templates to an almost finished pipe so you do not over- or under-bend the pipe. Using templates will speed up your work.

•If you pass the 45˚ angle mistakenly, you can sometimes reverse the pipe and slightly press it enough to reach the required 45˚.

•Bending any angle may thin and stress the walls and narrow the center of the pipe. If you need to make bends more than 100˚, we recommend heating the pipe during bending. Generally, heat weakens metal, but it will allow it to bend more freely.

•Pipes bent past 90˚ will flow into the bending die, making the pipe hard to remove after bending. Greasing the inside of the die will make this removal easier, or switching to a larger die for bending the last few degrees will eliminate this difficulty.

MAINTENANCE

•The Model G9017 and G9018 are basi- cally maintenance free. However, the oil level should be kept constant at about 2.5 pints of quality hydraulic oil.

•Too much oil will force the surplus oil to leak from the bottle jack fill plug (Figure 8), caus- ing a mess.

•Not enough oil will cause loss of power.

To add oil:

1.Set the tube bender upright, retract the piston rod fully and remove the fill plug (Figure 8).

NEW

PHOTO Oil Seal

Fill Plug

Figure 8. Fill Plug.

2.Fill the bottle jack to the level of the fill plug hole and replace the fill plug.

3.Place the tube bender in its operating posi- tion, fully extend the piston rod, then retract the rod to expel air in the bottle jack.

4.Remove the fill plug and repeat Steps 2 & 3 until all of the air is expelled.

If you need additional help with this procedure, call our Service Department at: (570) 546-9663.

G9017/G9018 specifications

The Grizzly G9017 and G9018 models are part of Grizzly Industrial's renowned lineup of woodworking machinery, renowned for their robust construction and advanced features tailored for both professional woodworkers and hobbyists. These tools are engineered to enhance efficiency and provide precision in various woodworking applications.

The Grizzly G9017 is a powerful Bandsaw featuring a 14-inch throat capacity, making it ideal for resawing larger cuts of wood. It is designed with a heavy-duty cast iron frame, which minimizes vibration and ensures stability during operation. The G9017 comes equipped with a powerful 1.5HP motor, providing ample power to cut through thick hardwood and softwood with ease. Additionally, this model features a tilting table, allowing for angled cuts and increased versatility.

The G9018, on the other hand, is a Drill Press that stands out for its unique features. It boasts a 16-speed gearbox, providing users the flexibility to select the best speed for their specific material and application. The G9018 also features a 3/4 HP motor that ensures robust performance across a wide range of drilling tasks. One of its key characteristics is the quick-release clamp, allowing for easy and efficient switching between drill bits.

Both models come standard with additional safety features, including blade guards on the Bandsaw and an emergency shut-off switch on the Drill Press. These features ensure a safer working environment, crucial for both beginners and professional woodworkers.

In terms of technology, Grizzly G9017 and G9018 incorporate user-friendly design principles. The Bandsaw provides easy adjustments for blade tension and tracking, while the Drill Press includes an easy-to-read depth stop for consistent hole depths.

Overall, the Grizzly G9017 and G9018 models combine rugged durability with high-performance capabilities, making them indispensable tools for any woodworking shop. With their powerful motors, versatile functions, and user-friendly designs, they are perfectly suitable for a variety of woodworking tasks, from intricate projects to larger cuts and drilling operations. Whether you're a seasoned woodworker or a newcomer to the craft, Grizzly's commitment to quality and innovation ensures these machines will meet and exceed expectations, paving the way for extraordinary woodworking results.