Faber INCA PRO 38 RB Venting Requirements, 630001732 or #, Electrical Requirements

Page 2

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or floor opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence that greatly reduces performance.

Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

FOR MORE SPECIFIC DUCTWORK INFORMATION, GO TO

PAGE 6.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

ATTENTION - This hood can only be used with the Faber 900 or 1200 cfm variable speed blower,

(part # 630001732 or # 610000007).

! WARNING

• To reduce the risk of fire and to properly exhaust air, you MUST terminate ductwork outside of the home

• DO NOT terminate the ductwork into spaces within the walls, ceilings, attics, crawl spaces or garages

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the flow of combustion and ventilation air.

• Failure to follow venting requirements may result in a fire.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with the electrical rating of this unit as specifiedon theserial/ratingplatelocated insidetheunit nearthe field wiring compartment. THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70

-latest edition, and all local codes and ordinances. Wire size and connections must conform with the rating of the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected directly to the fused disconnect (or circuit breaker) through flexible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the appliance can be moved if servicing is ever neces- sary. A UL Listed, 1/2" conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box)

For residential use only.

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood must be sanded until smooth. A hole through metal must have a grommet.

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOL- LOWING: Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOL- LOWING: Installation Work And Electrical Wiring Must Be Done By Qualified Person(s) In Accordance With All Applicable Codes And Standards, Including Fire-Rated Construction.

Sufficient air is needed for proper combustion and exhaust- ing of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

!WARNING

•Electrical ground is required on this rangehood.

•If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for grounding.

•DO NOT ground to a gas pipe.

•DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock.

•Check with a qualified electrician if you are in doubt as to whether the rangehood is properly grounded.

•DO NOT use this appliance with any solid state fan speed control device.

•Failure to follow electrical requirements may result in a fire.

Version 06/06 - Page 2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Lisez Bien Cette Fiche Avant Dinstaller LA Hotte Inca PRO 38 RBElectrical Requirements Venting Requirements630001732 or # For residential use onlyFiche Technique Électrique Règlements DévacuationLe système dévacuation Doit sortir à lextérieur Demande un bouche-trouVersion 06/06 For Installations with Liners Inca Pro 38 can be used with custom hoods 40 wide and upMake Your CUT-OUTS CUT-OUT Install the RangehoodPlan Your Ductwork Volt white supply wire Remove the two philips screws D in . Remove the entireWarranty & Service USE and Care InformationInstallation DE LA Hotte à la Installations Avec CadresDimensions DE LA Hotte ET Dimensions DU Cadre à la CUT-OUT Plan DU ConduitFaire LA Coupe Installation DE LA Hotte Retirer le bas de la hotteGarantie ET Service Utilisation ET Entretien

INCA PRO 38 RB specifications

The Faber INCA PRO 38 RB is a sophisticated range hood that combines powerful ventilation with stylish design, making it an excellent addition to modern kitchens. It stands out due to its impressive blend of aesthetics and functionality, ensuring that the cooking environment remains fresh and clean while enhancing the overall kitchen decor.

One of the key features of the INCA PRO 38 RB is its powerful motor. With a maximum extraction rate that can handle even the most demanding cooking tasks, this range hood efficiently removes smoke, steam, and odors from the kitchen, maintaining a comfortable cooking atmosphere. The range hood is equipped with three-speed settings, allowing users to adjust the airflow according to their cooking needs. Whether you are simmering a delicate sauce or frying foods that produce more smoke, Faber offers the flexibility to adapt ventilation to the intensity of each task.

The design of the INCA PRO 38 RB is a blend of modern aesthetics and practicality. Featuring a sleek, stainless-steel finish, it adds a touch of elegance to any kitchen design. The lightweight and compact design makes it suitable for various kitchen layouts without taking up too much space.

The hood employs advanced technologies for enhanced noise reduction, ensuring a quieter operation, so you can enjoy conversation and music while cooking. Additionally, the INCA PRO 38 RB comes with high-efficiency LED lighting, which not only illuminates the cooking area for precision but also adds an energy-efficient lighting solution.

Installation flexibility is also an important characteristic of the Faber INCA PRO 38 RB. It can be installed as a ducted or recirculating system, making it versatile for different kitchen setups. This versatility helps in adapting to various kitchen designs and ventilation requirements, further enhancing its appeal to homeowners and designers alike.

The grease filters in the INCA PRO 38 RB are easy to clean and are designed to capture grease effectively, ensuring that the air remains clean and free of contaminants. With its combination of advanced features, stylish design, and user-friendly operation, the Faber INCA PRO 38 RB remains a leading choice for those seeking a high-performance range hood that complements modern kitchen aesthetics while delivering exceptional performance.
Top Page Image Contents