Faber INCA PRO 38 RB Plan Your Ductwork, Make Your CUT-OUTS, CUT-OUT Install the Rangehood

Page 6

ATTENTION

This rangehood is designed to be connected to a remote blower (pur- chased separately). CAUTION: To reduce the risk of fire and electric shock, install this rangehood only with remote blowers rated a maxi- mum 1.8 Amp, suitable for use with solid state fan speed controls. The remote blower requires a separate wiring cable that should be installed at the same time that the ductwork is installed. For best results, 10” duct is recommended for the remote blower.

PLAN YOUR DUCTWORK

To ensure that the blower performs to its highest possible capacity, ductwork should be as short and straight as possilbe.

The ductrun should not exceed 55 equivalent feet if ducted using the required minimum of 10" round duct. Calculate the length of the ductwork by adding the equivalent feet in FIG- URE 2 for each piece of duct in the system An example is given in FIGURE 3.

45˚ Elbow

 

3.0 feet

90˚ Elbow

 

5.0 feet

90˚ Flat Elbow

12.0 feet

Wall Cap

 

0.0 feet

FIGURE 2

 

 

 

 

 

 

 

 

 

 

9 Feet Straight Duct 9.0 feet

2 - 90˚ Elbows

10.0 feet

Wall Cap

 

0.0 feet

 

Total System

19.0 feet

FIGURE 3

For best results, use no more than three 90° elbows. Make sure that there is a minimum of 24" of straight duct between elbows if more than one is used. Do not install two elbows together. If you must elbow right away, do it as far away from the hood's exhaust opening as possible.

MAKE YOUR CUT-OUTS

1.Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet or custom hood. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt.

2.Determine and clearly mark with a pencil the center line on the cabinet or custom hood where the rangehood will be installed.

3.Determine and make all necessary cuts in the wall and/or ceiling for the ductwork. Install the ductwork before the rangehood.

4.Determine the proper location for the Power Supply Cable. Use a 1 1/4" Drill Bit to make this hole. Install the cable. Use caulking to seal around the hole. DO NOT turn on the power until installation is complete.

5.Make the cut-out opening where the rangehood will be installed (FIGURE 4).

37"

CUT-OUT

14

5/8"

 

FIGURE 4

INSTALL THE RANGEHOOD

1.Remove the rangehood , as seen in (FIGURE 5) from the carton and place on a flat surface. Cover the surface to prevent accidental damage. Remove all parts including the literature package before discarding the carton.

FIGURE 5

Version 06/06 - Page 6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Lisez Bien Cette Fiche Avant Dinstaller LA Hotte Inca PRO 38 RBElectrical Requirements Venting Requirements630001732 or # For residential use onlyFiche Technique Électrique Règlements DévacuationLe système dévacuation Doit sortir à lextérieur Demande un bouche-trouVersion 06/06 For Installations with Liners Inca Pro 38 can be used with custom hoods 40 wide and upCUT-OUT Install the Rangehood Plan Your DuctworkMake Your CUT-OUTS Volt white supply wire Remove the two philips screws D in . Remove the entireWarranty & Service USE and Care InformationInstallations Avec Cadres Dimensions DE LA Hotte ET Dimensions DU Cadre à laInstallation DE LA Hotte à la Plan DU Conduit Faire LA CoupeCUT-OUT Installation DE LA Hotte Retirer le bas de la hotteGarantie ET Service Utilisation ET Entretien

INCA PRO 38 RB specifications

The Faber INCA PRO 38 RB is a sophisticated range hood that combines powerful ventilation with stylish design, making it an excellent addition to modern kitchens. It stands out due to its impressive blend of aesthetics and functionality, ensuring that the cooking environment remains fresh and clean while enhancing the overall kitchen decor.

One of the key features of the INCA PRO 38 RB is its powerful motor. With a maximum extraction rate that can handle even the most demanding cooking tasks, this range hood efficiently removes smoke, steam, and odors from the kitchen, maintaining a comfortable cooking atmosphere. The range hood is equipped with three-speed settings, allowing users to adjust the airflow according to their cooking needs. Whether you are simmering a delicate sauce or frying foods that produce more smoke, Faber offers the flexibility to adapt ventilation to the intensity of each task.

The design of the INCA PRO 38 RB is a blend of modern aesthetics and practicality. Featuring a sleek, stainless-steel finish, it adds a touch of elegance to any kitchen design. The lightweight and compact design makes it suitable for various kitchen layouts without taking up too much space.

The hood employs advanced technologies for enhanced noise reduction, ensuring a quieter operation, so you can enjoy conversation and music while cooking. Additionally, the INCA PRO 38 RB comes with high-efficiency LED lighting, which not only illuminates the cooking area for precision but also adds an energy-efficient lighting solution.

Installation flexibility is also an important characteristic of the Faber INCA PRO 38 RB. It can be installed as a ducted or recirculating system, making it versatile for different kitchen setups. This versatility helps in adapting to various kitchen designs and ventilation requirements, further enhancing its appeal to homeowners and designers alike.

The grease filters in the INCA PRO 38 RB are easy to clean and are designed to capture grease effectively, ensuring that the air remains clean and free of contaminants. With its combination of advanced features, stylish design, and user-friendly operation, the Faber INCA PRO 38 RB remains a leading choice for those seeking a high-performance range hood that complements modern kitchen aesthetics while delivering exceptional performance.
Top Page Image Contents