Venting Requirements, Electrical Requirements

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efﬁcient performance. The size of the ductwork should be uniform. Do not install two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or ﬂoor opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence that greatly reduces performance.

Make sure there is proper clearance within the wall or ﬂoor for exhaust duct before making cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

FOR MORE SPECIFIC DUCTWORK INFORMATION, GO

TO PAGE 4.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

!WARNING

•Venting system MUST terminate outside the home.

•DO NOT terminate the ductwork in an attic or other enclosed space.

•DO NOT use 4" laundry-type wall caps.

•Flexible-type ductwork is not recommended.

•DO NOT obstruct the ﬂow of combustion and ventilation air.

•Failure to follow venting requirements may result in a ﬁre.

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with the electrical rating of this unit as speciﬁed on the serial/rating plate located inside the unit near the ﬁeld wiring compartment. THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and ordinances. Wire size and connections must conform with the rating of the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

For residential use only.

This appliance should be connected directly to the fused disconnect (or circuit breaker) through ﬂexible, armored or nonmetallic sheathed copper cable. Allow some slack in the cable so the appliance can be moved if servicing is ever nec- essary. A UL Listed, 1/2" conduit connector must be provided at each end of the power supply cable (at the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood must be sanded until smooth. A hole through metal must have a grommet.

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI- CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRI- CAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:InstallationWorkAndElectricalWiringMust Be Done By Qualiﬁed Person(s) In Accordance With All Applicable Codes And Standards, Including Fire-Rated Construction.

Sufﬁcient air is needed for proper combustion and exhausting of gases through the ﬂue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire ProtectionAssociation (NFPA), and theAmerican Society for Heating, Refrigeration andAir Conditioning Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not dam- age electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors.

!WARNING

•Electrical ground is required on this rangehood.

•If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for grounding.

•DO NOT ground to a gas pipe.

•DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock.

•Check with a qualiﬁed electrician if you are in doubt as to whether the rangehood is properly grounded.

•Failure to follow electrical requirements may result in a ﬁre.

Version 12/04 - Page 2

PRO MAGNUMw specifications

Faber PRO MAGNUMW is an advanced professional hood designed for both performance and aesthetic appeal in modern kitchens. It stands out for its powerful ventilation capabilities, which are essential in maintaining a fresh and clean cooking environment. The hood is equipped with a high-efficiency motor that ensures excellent air extraction, effectively eliminating smoke, odors, and grease from the kitchen space.

One of the standout features of the PRO MAGNUMW is its impressive extraction rate. The model can provide up to 1200 m³/h of airflow, making it suitable for large cooking areas. This high extraction rate ensures that even the most rigorous cooking sessions do not compromise air quality.

The PRO MAGNUMW also incorporates advanced noise-reduction technology. This innovation allows for quieter operation, which is a significant consideration for many homeowners when choosing a kitchen hood. The combination of high-performance extraction and low noise levels creates a comfortable cooking atmosphere.

In terms of design, the Faber PRO MAGNUMW offers a sleek, contemporary aesthetic that complements a variety of kitchen styles. Its stainless steel finish is not only visually appealing but also easy to clean, ensuring that the hood maintains its pristine appearance over time.

Another notable characteristic is the efficient LED lighting integrated into the unit. This feature provides bright illumination over the cooking surface, enhancing visibility while preparing meals. The energy-efficient LED lights also contribute to lower energy consumption, aligning with eco-friendly practices.

The control system of the PRO MAGNUMW is user-friendly, often featuring a touch control interface or remote control options. This enables users to adjust fan speeds and lighting effortlessly. Moreover, many models come with programmable timers that allow for automatic shut-off, providing convenience and energy savings.

Installation flexibility is another advantage of the Faber PRO MAGNUMW. It can be mounted as a wall hood, chimney hood, or even as an island hood, making it versatile for various kitchen layouts.

Overall, the Faber PRO MAGNUMW combines powerful ventilation, low noise operation, modern design, and user-friendly features, making it an excellent choice for both professional chefs and home cooks who demand efficiency and style in their kitchen equipment.