Faber PRO MAGNUMw Prepare the Wall, Brackets are Securely Fastened to the Wall

Page 5

PREPARE THE WALL

1.Disconnect and move freestanding range from cabinet opening to provide easier access for installation. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt.

2.Determine and clearly mark with a pencil the center line on the wall where the rangehood will be installed.

3.The Pro Magnum attaches to the wall by mounting screws indicated in FIGURE 5. For the 30" and 36" models, there are two mounting screws. For the 48" model, there are four mounting screws. Install the screws into the wall. The screws should be inserted into the wall until the screw head is flush with the wall.

WARNING: THE SCREWS PROVIDED FOR MOUNTING THIS RANGEHOOD MUST BE INSERTED INTO SOLID WOOD. THESE MUST NOT BE INSERTED INTO SHEET ROCK.

If a backsplash is to be used with this rangehood, it must be installed before the rangehood. Installation instructions for the backsplash are supplied in its box. The height of the backsplash will determine the bottom edge of the canopy.

FIGURE 5

4.The Telescopic Chimney Kit and Full Width Duct Cover use different bracket systems to attach to the wall. FIGURE 6 provides the position for the telescopic chimney brackets.

FIGURE 6

FIGURE 7 provides the dimensions for the Full Width Duct Cover brackets. The Full Width Duct Cover also attaches to the top of the rangehood with screws provided. The Full Width Duct Cover must be attached to the top of the rangehood before mounting the rangehood to the wall.

FIGURE 7

Determine the proper location for each bracket and install the brackets on the wall. MAKE SURE THAT THE SCREWS

AND BRACKETS ARE SECURELY FASTENED TO THE WALL.

5.Determine and make all necessary cuts in the wall for the ductwork. The Pro Magnum vents either through the top or the rear of the rangehood. Each rangehood is shipped from the factory vented through the top. In order to vent to the rear, the blower inside the rangehood must be turned to the rear. The dimensions for the duct openings are given in FIGURE

8.The 48" model uses two 3 & 1/4" by 10" duct openings. Install all ductwork before installing the rangehood.

6.Determine the proper location for the Power Supply Cable as indicated in FIGURE 8. Note that the 30"/36" versions have the option of top or rear electrical connection while the 48" version has only the rear option. Use a 1 & 1/4" Drill Bit to make this hole. Run the Power Supply Cable. Use caulking to seal around the hole. DO NOT turn on the power until installation is complete.

30" AND 36" VERSIONS

Electrical Opening

48" VERSION

Electrical Opening

FIGURE 8

Version 12/04 - Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Read and Save These Instructions Lisez Bien Cette Fiche Avant Dinstaller LA HotteElectrical Requirements Venting RequirementsFor residential use only Ducted fans must always be vented to the outdoorsUniquement pour usage menager Règlements DévacuationFiche Technique Électrique Calculate the Ductrun Length Plan the InstallationBrackets are Securely Fastened to the Wall Prepare the WallInstall the Rangehood USE and Care Information Warranty & Service

PRO MAGNUMw specifications

Faber PRO MAGNUMW is an advanced professional hood designed for both performance and aesthetic appeal in modern kitchens. It stands out for its powerful ventilation capabilities, which are essential in maintaining a fresh and clean cooking environment. The hood is equipped with a high-efficiency motor that ensures excellent air extraction, effectively eliminating smoke, odors, and grease from the kitchen space.

One of the standout features of the PRO MAGNUMW is its impressive extraction rate. The model can provide up to 1200 m³/h of airflow, making it suitable for large cooking areas. This high extraction rate ensures that even the most rigorous cooking sessions do not compromise air quality.

The PRO MAGNUMW also incorporates advanced noise-reduction technology. This innovation allows for quieter operation, which is a significant consideration for many homeowners when choosing a kitchen hood. The combination of high-performance extraction and low noise levels creates a comfortable cooking atmosphere.

In terms of design, the Faber PRO MAGNUMW offers a sleek, contemporary aesthetic that complements a variety of kitchen styles. Its stainless steel finish is not only visually appealing but also easy to clean, ensuring that the hood maintains its pristine appearance over time.

Another notable characteristic is the efficient LED lighting integrated into the unit. This feature provides bright illumination over the cooking surface, enhancing visibility while preparing meals. The energy-efficient LED lights also contribute to lower energy consumption, aligning with eco-friendly practices.

The control system of the PRO MAGNUMW is user-friendly, often featuring a touch control interface or remote control options. This enables users to adjust fan speeds and lighting effortlessly. Moreover, many models come with programmable timers that allow for automatic shut-off, providing convenience and energy savings.

Installation flexibility is another advantage of the Faber PRO MAGNUMW. It can be mounted as a wall hood, chimney hood, or even as an island hood, making it versatile for various kitchen layouts.

Overall, the Faber PRO MAGNUMW combines powerful ventilation, low noise operation, modern design, and user-friendly features, making it an excellent choice for both professional chefs and home cooks who demand efficiency and style in their kitchen equipment.
Top Page Image Contents