Install the Rangehood

1.Remove the unit from the carton and place on a ﬂat surface for assembly. Cover the surface to prevent accidental damage. Remove all parts including the mounting hardware before discarding the carton.

2.Remove the grease ﬁlters USING TWO HANDS (one to hold the ﬁlter so that it doesn't fall on cooktop and one to turn the knob) by pulling the knob out and turning to the left.

3.The rangehood is shipped from the factory in the up vent position as indicated in FIGURE 9. For top vent applications, no additional adjustments are necessary.

FIGURE 9

For rear vent applications, the blower must be turned inside the rangehood so that the blower vents to the rear as indicated in FIGURE 10. The blower is turned by removing two screws on each side of the blower, rotating the blower with the exhaust opening facing the rear and then replace the screws. The exhaustcovermustbemovedtoblocktheunusedopening. The blower must be converted before installing the rangehood.

FIGURE 10

4.Remove the cover from the ﬁeld wiring compartment. Remove the wiring electrical knockout using a ﬂat-blade screwdriver. Feed the Power Supply Cable through the electrical knockout.

5.The canopy attaches to the wall by two screws discussed earlier in the installation instructions. The canopy hangs from these screws by brackets inside the rangehood shown in FIGURE 11. Before attempting to hang the canopy, you should rotate the adjustment screw marked V1 in FIGURE

11counterclockwise to extend the brackets from the canopy. Using a Phillips head screwdriver, rotate this screw counterclockwise to extend the bracket.

FIGURE 11

6.Install the damper before hanging the rangehood. The damper attaches to the rangehood by two small screws provided in the hardware package. If 48" hood is to be connected to 10" round duct, install the Duct Transition Kit now.

7.Hang the rangehood canopy from the screws. Due to the weight of the canopy, these screws must be installed into solid material! Once the canopy is hung, rotate the screw marked V1 to secure the rangehood to the wall.

MAKE SURE THAT THE RANGEHOOD IS SECURELY ATTACHED TO THE WALL! FAILURE TO PROPERLY INSTALL COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.

8.The brackets shown in FIGURE 11 are also used to adjust the level of the canopy. Using a Phillips screwdriver, rotate the screw V2 to adjust the level of the canopy.

9.Connect the Power Supply Cable to the rangehood. Attach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire connector. Attach the Black lead of the power supply to the Black lead of the rangehood with a twist-on type wire connector. Connect the Green ( Green and Yellow ) ground wire under the Green grounding screw.

10.Replace the ﬁeld wiring compartment cover and the grease ﬁlters.

11.If the installation uses a telescopic chimney, connect the ductwork and install the chimney. Mount the upper chimney section to the wall ﬁrst. Then mount the lower section. The lower section ﬁts over the upper section.

If the installation uses a full width duct cover, install it now.

12.Turn the power supply on. Turn on blower and light. The rangehood controls are located on the right-hand side under the canopy. If the rangehood does not operate, check that the circuit breaker is not tripped or the house fuse blown. If the unit still does not operate, disconnect the power supply and check that the wiring connections have been made properly.

Version 12/04 - Page 6

PRO MAGNUMw specifications

Faber PRO MAGNUMW is an advanced professional hood designed for both performance and aesthetic appeal in modern kitchens. It stands out for its powerful ventilation capabilities, which are essential in maintaining a fresh and clean cooking environment. The hood is equipped with a high-efficiency motor that ensures excellent air extraction, effectively eliminating smoke, odors, and grease from the kitchen space.

One of the standout features of the PRO MAGNUMW is its impressive extraction rate. The model can provide up to 1200 m³/h of airflow, making it suitable for large cooking areas. This high extraction rate ensures that even the most rigorous cooking sessions do not compromise air quality.

The PRO MAGNUMW also incorporates advanced noise-reduction technology. This innovation allows for quieter operation, which is a significant consideration for many homeowners when choosing a kitchen hood. The combination of high-performance extraction and low noise levels creates a comfortable cooking atmosphere.

In terms of design, the Faber PRO MAGNUMW offers a sleek, contemporary aesthetic that complements a variety of kitchen styles. Its stainless steel finish is not only visually appealing but also easy to clean, ensuring that the hood maintains its pristine appearance over time.

Another notable characteristic is the efficient LED lighting integrated into the unit. This feature provides bright illumination over the cooking surface, enhancing visibility while preparing meals. The energy-efficient LED lights also contribute to lower energy consumption, aligning with eco-friendly practices.

The control system of the PRO MAGNUMW is user-friendly, often featuring a touch control interface or remote control options. This enables users to adjust fan speeds and lighting effortlessly. Moreover, many models come with programmable timers that allow for automatic shut-off, providing convenience and energy savings.

Installation flexibility is another advantage of the Faber PRO MAGNUMW. It can be mounted as a wall hood, chimney hood, or even as an island hood, making it versatile for various kitchen layouts.

Overall, the Faber PRO MAGNUMW combines powerful ventilation, low noise operation, modern design, and user-friendly features, making it an excellent choice for both professional chefs and home cooks who demand efficiency and style in their kitchen equipment.