Hearth and Home Technologies BH 105 manual Venting

Page 10

Venting

Fig. 3

Avoiding Smoke and Odors - Negative Pressure, Shut-down and Electrical Power Failure.

To reduce the probability of back-drafting or burn back in the pellet boiler during a power failure, it must be able to draft naturally without exhaust blower operation. Negative pressure in the house will resist this natural draft if not accounted for during in- stallation. Heat rises in a house, and leaks out at upper levels. This air must be replaced with air from outside the dwelling, which normally flows into lower levels. Vents and chimneys into basements and lower levels can become the conduit for return air and reverse un- der these conditions.

Hearth & Home Technologies strongly recommends the use of outside air in all pellet boiler installa- tions, especially those on lower level and main floor locations. Per national building codes, consideration must be given to combustion air supply to all combus- tion appliances. Failure to supply adequate combustion air for all appliance demands may lead to back-draft- ing of those and other appliances within the home.

To reduce the probability of reverse drafting dur- ing shut-down conditions, Hearth & Home Tech- nologies strongly recommends:

Installing the pellet vent with a minimum vertical run of 5 feet. Preferably terminating above the roof line.

Installing the outside air intake at least four feet below the vent termination.

To prevent soot damage to exterior walls, and to pre- vent re-entry of soot or ash into the house:

Maintain specified clearances to windows, doors and air inlets, including air conditioners.

Vents should not be placed below ventilated soffits. Run the vent above the roof.

Avoid venting into alcove locations.

Vents should not terminate under overhangs, decks or onto covered porches.

Maintain minimum clearance of 12” from the vent termination to the exterior wall. Extending this dis- tance may be required if visual accumulation occurs.

10

Image 10
Contents Installation & Operating Manual BH 105 Pellet BoilerPage Parts Locations Table Of Contents IntroductionWarranty ECO-CHOICE Limited WarrantyAssembly Boiler Kit Materials Refer toDesign Installation is to be Performed by a Qualified Installer Venting Venting Ventingti g VentingVenting Installation Keep combustibles away From flue outletOutside Air Main Wiring Installation InstallingInstallationDuct Installing Duct/AirInstallationConditioning Installation Example of Typical Tankless Domestic HOT Water PipingUnion AIR Vent Installation Over Heat Safety Zone Power Failure / Heat Dissipation LoopDraft Test Procedure TestFuel Specifications Fuel and Fuel StorageOperation Status LightWithout the Outdoor Air Temperature Sensor Installed Control Board OperationPellet Boiler Outdoor Air Reset Operation Turn Mode Selector to OFF Starting a Fire AutomaticallyFlip the Igniter Switch up into the Auto position MAX. TempLighting a Fire Manually Have matches or other ignition source readyOperation Feeder Chamber Fig MaintenanceBurnpot Cleaning To remove the feeder coverOpen Ash Door Remove Ash PanCleaning Steps Combustion Blower Cleaning Helpful Hints TroubleshootingFuel Atmospheric Conversion Bh105 #8 Ash base Assembly Stocked at depot #28 Feeder Assembly #29 boiler Kit #30 water Plate Kit #31 handle Kit Description COmmENTS PArT NumbEr Hardware Packages BTU Input Range= 0, and 9350 to 113,900 SpecificationsElectrical 120 VAC 60 Hz Diagram Pellet Boiler Wiring DiagramPower Failure Backup Supply Testing Label BH105Service Record / Notes Proudly Printed On 100% Recycled Paper Quick Reference Auto-Light Signature of Boxer

BH 105 specifications

Hearth and Home Technologies BH 105 is a modern and versatile fireplace that combines functionality and aesthetic appeal. Designed for both residential and commercial spaces, it brings the warmth of a traditional fireplace with the convenience of contemporary technology. One of the standout features of the BH 105 is its impressive heating capacity, efficiently warming larger areas while maintaining a cozy atmosphere.

The BH 105 uses advanced combustion technology, which not only maximizes heat output but also minimizes emissions, making it an eco-friendly choice for homeowners. This fireplace achieves a commendable efficiency rating, ensuring that most of the heat generated is utilized effectively, reducing energy costs and environmental impact.

Aesthetically, the BH 105 offers a sleek and contemporary design that can seamlessly blend with any decor. The large viewing area features tempered glass, providing unobstructed views of the mesmerizing flames. This visual aspect enhances the ambiance of any room, making it a focal point in the home. The fireplace is available in various finishes, allowing homeowners to choose a style that complements their personal taste and existing interior designs.

User experience is a priority in the BH 105’s design. It includes features such as an easy-to-use control panel and a programmable thermostat that allows for precise temperature regulation. This user-friendly interface enables individuals to set their desired comfort levels with ease.

The BH 105 also comes equipped with safety features like an automatic shut-off system, ensuring peace of mind for users, especially in households with children or pets. The durability of the materials used in its construction ensures that the fireplace can withstand the rigors of regular use while maintaining its aesthetic charm.

In summary, Hearth and Home Technologies BH 105 is a perfect embodiment of modern fireplace technology, offering high efficiency, stunning design, and user-friendly features. Whether for heating a living room or creating a cozy atmosphere in a commercial setting, the BH 105 stands out as an exceptional choice for discerning individuals seeking warmth without compromising on style.