Zanussi ZKG6040 Care and cleaning, Cleaning materials, Cleaning the outside of the appliance

Page 27

Care and cleaning

WARNING!

Before cleaning always allow the appliance to cool down before switching off at the electricity supply.

Cleaning materials

•Before using any cleaning materials on your appliance, check that they are suitable and that their use is recommended by the manufacturer.

•Cleaners that contain bleach should not be used as they may dull the surface finishes. Harsh abrasives and scourers should also be avoided.

Cleaning the outside of the appliance

•Do not use abrasive cleaning materials e.g. abrasive cream cleaners, wire wool pads or scourers on painted or printed finishes as damage may occur. Regularly wipe over the control panel, control knobs, handles, doors and appliance sides using a soft cloth and hot soapy water. To prevent streaking, finish with a soft cloth.

•Stainless Steel cream cleaners are abrasive and should be avoided as they may dull the surface finish. Any spillage on the stainless steel finish must be wiped off immediately.

WARNING!

Do not attempt to remove any of the control knobs from the appliance as this may cause damage and is a safety hazard.

Cleaning the hob

•Clean the hob using a mild abrasive.

•Take care not to damage the spark electrodes. If the spark electrodes are damaged the burners will not light. You can remove the pan supports, burner caps and burner crowns to clean them. Again take care not to damage the spark electrodes.

•Clean the burner crowns and pan supports by soaking them in very hot soapy water.

•Aluminium based saucepans can leave shiny metal marks on the pan supports. You can remove any stubborn stains by scouring with a soap impregnated steel wool pad. If you look after the burner crowns and pan supports in this way they will stay reasonably clean. However the surface will dull with time. After cleaning the appliance parts, dry them thoroughly before you put them back.

When replacing hob burner parts

1.Crown to body. (Do not try to force the crown on to the body). Make sure that the hole in the crown is over the electrode. Check that the location pegs sit in the slots in the body. When the crown is in this position let it fall freely on to the body. Check that the crown can be moved slightly from side to side.

2.Cap to crown. Place cap centrally on the top of crown (enamel side up). Move sideways and front to back to check the cap is properly fitted.

3.Check for ignition. If a burner will not light then you need to check the crown and cap positions.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents User Manual Cooker Contents During use Important safety instructionsInstallation Child safetyCleaning and maintenance Controls and their functions Product descriptionPreparing to use your appliance Before using the applianceRating plate CookwareGrill and oven furniture Electronic timer To set the time of dayTo set the countdown Neon flashes To cancel the countdownCountdown indicator Press the selectorThat the correct time of day is displayed To set the timer to switch on and off automaticallyTo set the timer to switch off only Buttons Cook time indicatorTo stop the sound To the time of dayTo turn off any burner Highest settingHob To light the hob burnersAny spillage should be removed from the lid before opening Things to noteHints and tips Do not overfill pans or they will boil overControl knob to Using the grillGrill To turn off the grillGrill pan and handle Button onSlide the handle Towards the right Food should be turned over during cooking as required Grilling chartTo turn the top oven off Using the top ovenTop oven PreheatingTo fit the top oven shelf Heat zones Using the main ovenTo install a shelf, reverse the above steps Main ovenTo turn the main oven off Approximate Cook time m Oven cooking chartOven cooking chart Cooking time Roasting chartSlow cook Using slow cookGeneral points Food preparation slow cookingCleaning the hob Care and cleaningCleaning materials Cleaning the outside of the applianceCleaning the grill Cleaning the grill and oven furnitureCleaning the doors To remove the inner glassTo replace the inner glass To clean the inner glass door panels Replacing an oven light bulbType of bulb required is a 300C 25 watt small Edison Screw Problem TroubleshootingHob burners will not light Flame colour is orange/yellow 600mm to front of door panel 66Kg 2mm minimum clearance Technical dataHeight Width Depth Weight Gas connection Electrical connection120 Heat input 0kW 9kW 3412 Btu/h 6483 Btu/h070 096 Heat InputNatural Gas versions of this appliance are available Installation instructionsImportant safety requirements Provision for ventilationAppliance For your safetyMoving your appliance Location of applianceBy the earth symbol or coloured green or green and yellow Leveling the applianceIf the fitted plug is removed Connecting to gas supply If a moulded plug is fittedFitting the stability chain Checking the top oven Pressure testingChecking the grill Checking the hobChecking the main oven light Energy save modeEnvironment Checking the main ovenStandard guarantee conditions Guarantee / Customer carePage Page 349143200 12/2006 Subject to change without notice
Top Page Image Contents