Zanussi DE 4744 Operating sequence, Check the filters, Load the dishes, Measure out detergent

Page 16

Operating sequence

1. Check the filters

Ensure they are clean and properly positioned (see "Maintenance and cleaning").

2. Press the ON-OFF push button

The ON-OFF indicator light will come on.

3. Check that there is rinse aid and salt

The corresponding indicator lights will illuminate if refilling is necessary.

4. Load the dishes

Remove any scraps of food.

Pull the lower basket out and arrange the saucepans, plates and cutlery in it.

Pull the upper basket out and arrange the plates, saucers, glasses and cups etc. in it.

Slide the baskets back into the machine.

5.Ensure that the spray arms can rotate freely.

6.Measure out detergent

Add the required amount of detergent into the dispenser according to the recommended quantity given in the Washing programmes chart.

Important!

If the half load option is selected remember to reduce the quantity of detergent.

Close the detergent dispenser lid.

7. Close the dishwasher door

8a. Setting and starting the programme without DELAY START

Press the push button corresponding to the wanted programme: the indicator light corresponding to the programme illuminates

and the phase indicator lights foreseen for that programme start flashing.

Select, if required, the

HALF LOAD

option.

The start of the programme will occur after about 6 seconds from the last pressure of a push button (programme or HALF LOAD push button), in this time it is possible to change programme simply pressing the push button of another programme.

Once the programme has started the phase indicator lights will turn off except for the phase under way.

It is possible to interrupt the programme by:

opening the door

pressing the ON-OFF push button (in this case all the indicator lights turn off)

Close the door again o press the ON-OFF, the programme will start from the point in which it was interrupted.

8b. Setting and starting the programme with DELAY START

The setting of the delay start occurs before selecting the programme.

Press the DELAY START push button and selected the desired time (3, 6 or 9 hours) until the indicator light corresponding to the chosen

hours flashes.

Press the push button corresponding to the wanted programme: the indicator light corresponding to the programme illuminates

and the phase indicator lights foreseen for that programme start flashing.

The start of the countdown will occur after about 6 seconds from the last pressure of a push button (programme or HALF LOAD push button).

The countdown will decrease with step of 3 hours and you are informed of this by the indicator lights of the hours.

16

Image 16
Contents Dishwasher Contents Important safety information InstallationChild Safety During UseDescription of the appliance Upper basketSID detergent dispenser WorktopON-OFF indicator light ON-OFF push button Door handle Delay Start push buttonIndicator lights Control panelBefore use Setting the water softenerPress Intensive SID To change the level, press ExampleIntensive SID 80 programme push button, level 4 is selected Intensive SID 80 programme push button, level 1 is selectedFilling with salt To fillTo fill with salt, unscrew the cap of the salt container First timeAdjusting the dose Rinse aidFilling with rinse aid Washing programmeUsing your appliance Loading your applianceLower basket Open the door and slide out the baskets to load the dishesCutlery basket Removable knife basketAdjusting the height of the upper basket Upper basketUse of detergent Compact detergents with enzymesHints and tips To save energyFor best washing results Items not suitable for dishwashersWashing programmes Operating sequence Check the filtersLoad the dishes Measure out detergentTo cancel a programme in progress Programme in progress can be cancelled at any timeIt is now possible to select a new washing programme PreviousInternal cleaning Cleaning the filtersCleaner Dishwasher CleanerExternal cleaning Frost precautionsLeave the inside of the machine clean Moving the machineSymptom Fault code Solution Something not workingProtection against flooding Case of malfunction,Technical specifications Hints for test centresInstallation instructions Water supply connectionsRemove all packaging before positioning the machine This dishwasher must be plumbed into a cold water supplyWater outlet hose connection We advise you therefore to remove itElectrical connection EarthBlue Brown LiveFitting under a counter LevellingKitchen worktop or sink 570-600Page From the Electrolux Group. The world’s No.1 choice