![](/images/new-backgrounds/1085043/8504333x1.webp)
Securing under a counter
Levelling
A |
II03 |
Important! |
Secure the dishwasher to the counter on the front part by means of two 4,2x13 screws provided (see fig. - point A).
Make sure that the dishwasher door closes properly, without rubbing on sides. Otherwise level the machine by slightly screwing or unscrewing the two front feet until perfect closure of the door is reached.
Kitchen plinth adjustment
To allow correct opening of the door it is sometimes necessary to cut the kitchen plinth. Refer to the cutting table below.
The dishwasher must be secured against tilting. Therefore, make sure that the counter it is fitted under, is suitably secured to a fixed structure (adjacent kitchen cabinets, wall).
Attention!
When the dishwasher is secured to the kitchen cabinets, do not drill any holes into the sides of the machine.
Adjusting the door balance
After fitting the door panel, the adjustment of the door
a
According to dimensions of
(a)and (b) as shown on the figure, you will find on the following table the depth (x) of the cut to be made on the plinth.
balance may be necessary.
II15
b
The door of the dishwasher is balanced when it is open in any position.
The dimensions (a) and (b) of the table are those more frequently used in the kitchen furnitures.
45° |
II09 |
Attention! |
For this purpose use the two front screws. Open the door, remove the caps and screw or unscrew the screws.
In this way the tension of the door balancing springs is increased or decreased respectively. Insert the caps again.
Height (a)*
|
| 1 7 0 | 1 6 0 | 1 5 0 | 1 4 0 | 1 3 0 | 1 2 0 | 11 0 | 1 0 0 |
|
|
|
|
|
|
|
|
|
|
| 40 | 136 | 131 | 125 | 118 | 110 | 100 | 93 | 85 |
|
|
|
|
|
|
|
|
|
|
| 50 | 135 | 131 | 125 | 118 | 110 | 102 | 92 | 85 |
|
|
|
|
|
|
|
|
|
|
(b)* | 60 | 137 | 132 | 125 | 118 | 110 | 102 | 94 | 85 |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
The weight of the panel should be within the limits given in the "dimensions of the panel", otherwise balancing the door will not be possible.
Depth | 70 | 138 134 128 | 120 110 104 | 95 | 85 |
| X | ||||||||
80 | / | 139 | 130 | 124 | 115 | 105 | 98 | 88 |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 90 | / | / | 138 | 129 | 120 | 110 | 100 | 90 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 0 0 | / | / | / | 135 | 125 | 115 | 105 | 95 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*dimensions in mm |
|
| 450 mm |
|
|
|
|
| |||||||
|
|
|
|
| (minimum) |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
X Dimensions of the cut on the plinth
PII06GB
17