Zanussi ZSF 4111 manual Prior to using for the first time, Water softener, Examples, End of cycle

Prior to using for the first time

Before using your dishwasher for the first time:

1.Ensure that the electrical and water connections comply with the installation instructions

2.Remove all packaging from inside the appliance

3.Set the water softener

4.Pour 1 litre of water inside the salt container and then fill with dishwasher salt

5.Fill the rinse aid dispenser

The water softener

The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance.

The higher the content of these minerals and salts, the harder your water is.

Water hardness is measured in equivalent scales, Clarke degrees, French degrees and mmol/l (millimol per litre).

The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.

The water softener must be set in both ways: manually, using the water hardness switch and electronically, using the function push buttons on the control panel.

a) Setting manually

1.Open the dishwasher door.

2.Remove the lower basket from the dishwasher.

3. Turn the water hardness switch to position 1 or 2 (see table).

4.Replace the lower basket.

b)Setting electronically

(The dishwasher must be switched off)

The dishwasher is factory set at level 5.

1. Press the On/Off button. The On/Off indicator light

illuminates (setting mode).

If a programme button indicator light is on, this means that

a washing programme has been set. The programme must

be cancelled: press simultaneously the function buttons 2

and 3 for about 2 seconds.

All the indicator lights will turn off (except for the On/Off

indicator light and eventually salt and rinse aid indicator

lights) indicating that the set programme has been

cancelled and the machine is now in setting mode.

2. Press simultaneously function buttons 2 and 3, until the

indicator lights of the function buttons 1, 2 and 3 start

flashing.

3. Press the function button 1, the indicator lights of function

buttons 2 and 3 turn off while the indicator light of the button

1 goes on flashing, at the same time the indicator light

End of cycle starts to flash.

The current level is indicated by the number of flashes of

the indicator light End of cycle (see chart).

Example: 5 flashes = level 5

4. To change the level, press button 1. Each time the button is

pressed the level changes. (For the selection of the new

level see the chart).

Examples:

if the current level is 5, by pressing button 1 once,

level 6 is selected.

if the current level is 10, by pressing button 1 once,

level 1 is selected.

The dishwasher is factory set at position 2.

AA07

After about 5 seconds the indicator light of the function

button 1 starts flashing, indicating the new selected level.

5. To memorise the operation, switch off the dishwasher by

pressing the On/Off button or wait about 60 seconds after

which the dishwasher will automatically return to

setting mode.

	Water hardness			Adjusting the water		Number of	Use
Clarke	°TH	mmol/l	Range	hardness setting		flashes of the	of salt
degrees	(french degrees)	(millimol per litre,				"End of cycle"
		international unit for the
		hardness of water)		manually	electronically	indicator light
64 - 88	91 - 125	9,0 - 12,5	VI	2	level 10	10	yes
53 - 63	76 - 90	7,6- 8,9	VI	2	level 9	9	yes
46 - 52	65 - 75	6,5 - 7,5	VI	2	level 8	8	yes
36 - 45	51 - 64	5,1 - 6,4	VI	2	level 7	7	yes
28 - 35	40 - 50	4,0 - 5,0	VI	2	level 6	6	yes
23 - 27	33 - 39	3,3 - 3,9	III	2	level 5	5	yes
18 - 22	26 - 32	2,6 - 3,2	III	1	level 4	4	yes
13 - 17	19 - 25	1,9 - 2,5	II	1	level 3	3	yes
5 - 12	7 - 18	0,7 - 1,8	I/II	1	level 2	2	yes
< 5	< 7	< 0,7	I	1	level 1	1	no

6