Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an enginee | r. |
The dishwasher is fitted with a number of alarm systems which can help you to quickly determine the cause of any problems. |
|
If the dishwasher will not start or stops during operation, all push buttons are inoperative except for the On/Off push button, | all the |
indicator lights turn off and in the digital display one of the following flashing fault codes will appear: AL1, AL2, AL3, AL4, | AL5, AL6, |
AL7, AL8. |
|
Press the On/Off push button to switch off the dishwasher and carry out the following suggested corrective actions listed below | . |
Once the checks have been carried out switch on the dishwasher and start a washing programme, if the fault code reappears in |
|
the digital display, contact your local Service Force Centre. |
|
Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or installation a ch | arge will |
be made, even if the appliance is in guarantee. |
|
Symptom | Fault code | Solution |
|
|
|
|
|
|
|
| |
The machine will not start |
|
| ● The door has not been properly closed. | Indicator light | |
|
|
| "open door" illuminates. |
| |
|
|
| ● The plug is not properly inserted in the power socket. |
| |
|
|
| ● There is a power failure. |
| |
|
|
|
|
| |
The machine does not fill | Indicator light |
| ● Ensure the water tap is open. |
| |
with water | "water tap" flashes |
| ● Ensure the mains water supply has not been cut off. |
| |
| and/or alarm AL5 |
| ● The inlet | hose may be squashed or bent. Reposition the hose. | |
|
|
| ● The inlet hose may be blocked. Switch off the water supply |
| |
|
|
| and clean the filter. |
| |
|
|
|
|
| |
The dishwasher will not drain | Alarm AL6 |
| ● The drain hose may be squashed or bent. Reposition the |
| |
|
|
| hose. |
|
|
|
|
| ● The sink may be blocked. Clear any blockages. |
| |
|
|
| ● The drain hose extension is not correct. Follow the instructions | ||
|
|
| for connecting to the waste. |
| |
|
|
| ● There is no vent in the end of the drain hose. |
| |
|
|
|
|
| |
Protection against flooding | Alarm AL4 |
| ● Close the water tap and contact the Service Force Centre. |
| |
is active |
|
|
|
|
|
|
|
|
|
| |
General | Alarms AL1, AL2, |
| ● Switch off the dishwasher. Switch it back on and start the |
| |
| AL3, AL7, AL8 |
| programme. If the alarm reappears, call the local Service |
| |
|
|
| Force Centre. |
| |
|
|
|
|
| |
The machine is noisy |
|
| ● Dishes are rattling against each other, refer to “Loading |
| |
|
|
| your machine”. |
| |
|
|
| ● The spray arms are knocking against the dishes. Refer |
| |
|
|
| to "Loading your machine". |
| |
|
|
|
|
| |
The door is difficult to close |
|
| ● The dishwasher is not level, or not properly |
| |
|
|
|
|
| |
Visible lime deposits or |
|
| ● Check that there is salt and that the salt cap is tight. |
| |
white film on the dishes |
|
| ● Check that the right level of the water softener is setted. |
| |
|
|
|
|
| |
The dishes are not quite dry |
|
| ● The rinse aid has run out or too little is being used | . | |
|
|
|
|
| |
The dishes are not clean |
|
| ● The baskets are too full. |
| |
(poor wash) |
|
| ● The dishes have not been arranged properly. |
| |
|
|
| ● The spray arms do not rotate |
| |
|
|
| ● The spray arms are clogged. |
| |
|
|
| ● The filters are clogged. |
| |
|
|
| ● The filters are not in the correct position. |
| |
|
|
| ● Not enough detergent has been used or it is unsuitable. |
| |
|
|
| ● The detergent is old or has gone hard. |
| |
|
|
| ● The salt container cap is not properly closed. |
| |
|
|
| ● The washing programme selected is too gentle. |
| |
|
|
|
|
|
|
15