Zanussi ZCE 700 manual Electrical connections, Supply Cable Specifications

Page 26

Electrical connections

Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.

THIS COOKER MUST BE EARTHED.

The manufacturer declines any liability should these safety measures not be observed.

This cooker is designed to be connected to a 230- 240V 50Hz AC electrical supply.

Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate. The rating plate is located on the bottom of the hob. A copy is attached on the back cover of this book.

The cooker is supplied without supply cord. A 3 core flexible supply cord must be fitted, in accordance with the specification given in the relevant tables.

Φ1) Loosen the two fixing screws securing the back protective screen of the cooker, then lift it up and remove it. This will expose the terminal block on the right bottom corner.

The cooker should be connected to a double pole switch with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch should be sited within 2m of the hob and be easily accessible upon completion of the installation.

The switch must not break the yellow and green earth cable at any point.

Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C.

Supply Cable Specifications

For Uk use only

 

 

 

 

 

 

Connection

Min. size

Cable / flex

Fuse

via

Cable/flex

type

 

 

 

 

 

• Cooker

3 x 6 mm2

H05 VV-F

30A

Control

 

 

 

Circuit

 

 

 

 

 

 

 

For Europe use only

2)Loosen the two cable clamp screws and lift the top section of the clamp enough to allow the cable to be passed through.

3)Connect the red (live) wire to the terminal which is marked with the letter "L".

4)Connect the black (neutral) wire to the terminal which is marked with the letter "N".

5)After fitting a green or yellow/green sleeve over the bare copper wire (earth wire), connect the exposed end to the terminal which is

marked with the earth symbol or with the letter "E" coloured green and yellow.

NOTE:

The earth wire should be about 2 cm. longer than the live and neutral wires.

6)Secure the cable by means of the clamp screws and refit the back protective screen.

Min. size Cable/flex

Cable / flex type

Fuse

 

 

 

 

 

 

 

 

 

 

 

 

 

3x 2.5 mm2

H05 RR-F

30 A

 

 

 

 

 

H05V2V2-F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FO 2375

26

Image 26
Contents Electric Cooker Important Safety Information Contents Oven Cavity Accessories Description of the CookerDisplay Control PanelCeramic hob cooking zones Double and oval cooking zones OperationChec control Keep-warm cooking zoneAutomax Connection of child safety device on zonesResidual heat indicator Chec control AutostopEnergy consumption Using the ceramic glass hobCeramic glass surface Saucepans and frying pansThermostat Control Knob Electric OvenOven Function Control Knob Oven Function Control LightBefore the First Use of the Cooker Using the OvenUsing the ceramic hob for the first time Heating up for the first timeCondensation and steam Hints and TipsTelescopic shelf supports CookwareTop oven element only Using the Conventional OvenHow to Use the Conventional Oven Hints and TipsConventional Oven Cooking Chart Roasting ChartHow to Use the Fan Oven ΦHow to Use DefrostingFan Oven Cooking Chart Defrosting ChartHow to Use the Grill GrillingSpecial problems Stain removal Cleaning the Ceramic HobCleaning after each use Replacing the Oven Light Cleaning the OvenOven Cavity Oven Shelves and Shelf Supports To clean the grease filterGrease Filter Service and Spare Parts Something not workingGuarantee Conditions Customer Care DepartmentZanussi Service Force Midlands London & Eastanglia Technical Data Instructions for the InstallerImportant Safety Requirements LocationFeet Assembly Splash back AssemblySupply Cable Specifications Electrical connectionsCustomer Care Height indicator for feet adjustment