Sherwood R-903 Speaker placement, Front left and right speakers and center speaker, Subwoofer

Page 18

ENGLISH

For your reference, the sound from each channel can be reproduced according to the surround modes as follows:

 

Channels

FRONT L/R

CENTER

SURROUND

SURROUND BACK

SUBWOOFER

Modes

 

L/R

 

 

 

 

 

 

 

 

 

 

 

 

DTS

 

 

 

 

 

 

DTS ES DISCRETE/MATRIX

DTS NEO MOVIE/MUSIC

DOLBY DIGITAL

DOLBY DIGITAL EX

DOLBY PRO LOGIC

DOLBY PRO LOGIC II MOVIE/MUSIC

DOLBY VIRTUAL

MPEG

MATRIX

Other Surround

STEREO

7 CH DIRECT

Depending on the speaker settings and the number of the encoded channels, the sound from the corresponding channels cannot be reproduced.(For details, refer to “Adjusting the speaker settings” on page 19.)

Speaker placement

Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows :

Front left and right speakers and center speaker

Place the front speakers with their front surfaces as flush with TV or monitor screen as possible.

Place the center speaker between the front left and right speakers and no further from the listening position than the front speakers.

Place each speaker so that sound is aimed at the location of the listener’s ears when at the main listening position.

Surround left and right speakers

Place the surround speakers approximately 1 meter (40 inches) above the ear level of a seated listener on the direct left and right of them or slightly behind.

Surround back speaker

Place the surround back speaker at the rear center facing the front at a slightly higher position (0 to 10 inches) than the surround speakers. We recommend installing the surround back speaker at a slightly downward facing angle. This effectively prevents the surround back channel signals from reflecting off the TV or screen at the front center, resulting in interference and making the sense of movement from the front to the back less sharp.

Subwoofer

The subwoofer reproduces powerful deep bass sounds.

Place a subwoofer anywhere in the front as desired.

Notes :

When using a conventional TV , to avoid interference with the TV picture, use only magnetically shielded front left and right and center speakers. To obtain the best surround effects, the speakers except the subwoofer should be full range speakers.

 

 

TV or SCREEN

 

 

 

1

 

 

SUBWOOFER CENTER

 

FRONT (LEFT)

3

4

FRONT (RIGHT)

 

 

 

2

 

 

5

 

 

LISTENING

 

 

 

POSITION

 

6

 

 

7

SURROUND

 

 

SURROUND

(LEFT)

 

9

(RIGHT)

 

 

8

 

 

 

SURROUND

 

 

 

(BACK)

 

Surround speaker

Surround back

 

 

 

speaker

Point slightly

 

 

 

Front speaker

 

downward

 

 

60 to 90 cm

18

Image 18
Contents Page Page Introduction Read this Before Operating Your UnitContents System Connections VideoConnecting Audio Components Video AC Input Cord Front Panel Controls Fluorescent DisplayUniversal Remote Controls DeviceFunction Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup codeUsing a punch-through function Removing a punch-through functionTo remove a macro program Programming a macro functionOperating a macro function To change a macro programBefore Operation Surround modesDolby Virtual Dolby Pro LogicDolby Pro Logic II surround Mpeg MultichannelSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back speakerAdjusting the speaker settings Setting the type of speakersSpeaker distance settings Refer to the previous page and adjust the speaker settings Turning the Power ON/OFF OperationsWhen AUX, Video 1~3 is selected as an input source When selecting the 7 CH DirectMute Selecting the surround mode To cancel the surround mode for stereo operationEnjoying Surround Sound Adjusting each channel level with test tone Adjusting each channel levelPresetting and Calling the channel levels Presetting the channel levelsCalling the channel levels Adjusting the LFE level Adjusting the tonebass and trebleCompressing the dynamic range Dolby Digital sources only Center width controlC-WID, default value Adjusting the Dolby Pro Logic II Music parametersPanorama modePANO, default value OFF Dimension controlDIMEN, default valueDownmixing into 2 front channels Manual tuning Auto tuningListening to Radio Broadcasts Presetting radio stations Tuning to preset stationsScanning preset stations in sequence TP search Listening to RDS Broadcastsfm onlyRDS search PTY searchEON PTY EON Enhanced Other Networks informationRecording with Tape Dubbing the audio and video signalsAnalog AUDIO/VIDEO Recording Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Using the OSD Current Status DisplayMenu Screen Select the desired menu using When selecting the CH Level Setup When selecting the Auto OSDTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetting UP the System on Front Panel AppendixInitializing the System Pano OFF Setup Code Table Inno HIT VCR Otto Verand DVD SAT AUX-TAPE/MD

R-903R, R-903 specifications

The Sherwood R-903 and R-903R are distinguished models in the realm of audio receivers, showcasing a blend of classic design and cutting-edge technology. These receivers are engineered for both audiophiles and casual listeners, providing a versatile and powerful home audio experience.

The R-903 features a robust 100 watts per channel output, ensuring that even the most demanding audio applications are handled with ease. Its power output makes it suitable for driving a variety of speaker configurations, enabling rich and immersive sound quality. The R-903R enhances this experience with refinements that include upgraded circuitry and improved performance metrics, delivering even cleaner audio fidelity.

One of the standout characteristics of these models is their extensive connectivity options. Both the R-903 and R-903R are equipped with multiple HDMI inputs, allowing seamless integration with modern devices such as Blu-ray players, gaming consoles, and streaming media players. This facilitates an all-in-one entertainment hub, perfect for enjoying movies, music, and gaming with minimal hassle.

The receivers boast advanced audio decoding technologies, including support for Dolby TrueHD and DTS-HD Master Audio. This ensures that users can experience high-resolution audio formats with stunning clarity, making every listening session captivating. Furthermore, they incorporate digital signal processing (DSP), which optimizes sound output based on the acoustics of the listening environment, providing a custom-tailored audio experience.

In terms of user interface, both models feature an intuitive on-screen setup that simplifies installation and configuration. The remote control is thoughtfully designed, giving users easy access to a variety of features, including preset audio modes, equalizer settings, and source selection, making it user-friendly for individuals of all technical backgrounds.

Additionally, both the R-903 and R-903R come with Bluetooth connectivity, granting users the ability to wirelessly stream music from smartphones, tablets, and other compatible devices. This modern feature enhances convenience while preserving the high-fidelity sound that Sherwood is known for.

In summary, the Sherwood R-903 and R-903R are exemplars of modern audio receivers, merging traditional strengths with innovative technologies. Their powerful output, extensive connectivity, and advanced audio processing capabilities make them ideal choices for anyone looking to elevate their sound experience in home entertainment. Whether for music, movies, or gaming, these receivers deliver unmatched performance and versatility.