Before Starting

Fig. 4

INSTALLATION INSTRUCTIONS FOR FREESTANDING ELECTRIC RANGE

Tools You Will Need

For leveling legs and Anti-Tip Bracket:

• Adjustable wrench or channel lock pliers

• 5/16" Nutdriver or Flat Head Screwdriver

• Electric Drill & 1/8" Diameter Drill Bit (Masonry Drill Bit if installing in concrete)

For electrical supply connection:

• 1/4" & 3/8" Socket driver or Nutdriver

Additional Materials You Will Need:

• Power Supply Cord or

•Copper Electrical Wiring & Metal Conduit (for hard wiring)

NORMAL INSTALLATION STEPS

1.ANTI-TIP BRACKET INSTALLATION INSTRUCTIONS - IMPORTANT SAFETY WARNING

To reduce the risk of tipping of the range, the range must be secured to the floor by properly installed Anti-Tip Bracket and screws packed with the range. Failure to install the anti-tip bracket will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself.

If range is ever moved to a different location, the Anti-Tip Bracket must also be moved and installed with the range.

Instructions are provided for installation in wood or cement fastened to either the floor or wall. When installed to the wall, make sure that screws completely penetrate dry wall and are secured in wood or metal. When fastening to the floor or wall, be sure that screws do not penetrate electrical wiring or plumbing.

1a. Locate the Bracket using the Template - (Bracket may be located on either the left or right side of the range. Use the information below to locate the bracket if template is not available).

Mark the floor or wall where left or right side of the range will be located. If rear of range

is against the wall or no further than 1-1/4" from wall when installed, you may use

the wall or floor mount method. If molding is installed

and does not allow the bracket to fit flush against the wall, remove molding or mount bracket to the floor. For wall mount, locate the bracket by placing the back edge of the template against the rear wall and the side edge of template on the mark made referencing the side of the range (See Fig. 4). Place bracket on top of template and mark location of the screw holes in wall. If rear of range is further than 1-1/4" from the wall when installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. Mark the location of the screw holes, shown in template. 1b. Drill Pilot Holes & Fasten Bracket - Drill a 1/8" pilot hole where screws are to be located. If bracket is to be mounted to the wall, drill pilot hole at an approximate 20° downward angle (See Fig. 5).

If bracket is to be mounted to masonry or ceramic floors, drill a

3/16" pilot hole 1-3/4" deep. The screws provided may be used in wood or concrete material. Use a 5/16" nut-driver or flat head screwdriver to secure the bracket in place (See Fig. 6). 1c. Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench. NOTE: A minimum clearance of 1/8" is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments. Slide range back into position (See Fig. 7).

Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage drawer. For models with a Warmer Drawer or broiler compartment, grasp the top rear edge of the range and carefully attempt to tilt it forward.

Fig. 5

Fig. 6

Fig. 7

2.ELECTRICAL CONNECTION REQUIREMENTS - This appliance must be properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/ NFPA No. 70 -- latest edition -- and Local Electrical Code requirements.

This appliance may be connected by means of "Permanent Wiring" or "Power Supply Cord Kit."

When installing Permanent Wiring, do not leave excess wire in range compartment. Excess wire in the range compartment may not allow the Rear Access Cover to be replaced properly and could create a potential electrical hazard if wires become pinched. Connect only as instructed under "Permanent Wire Connections" in Step 4c. When using flexible conduit or range cable use flex connector or range cable strain relief (Fig. 11).

2a. Models with Factory Connected Power Supply Cord. NOTE: Some models may have a factory

installed three (3) conductor Power Supply Cord.

Mobile home installations, new branch circuit installations (1996NEC) or areas where Local Codes do not permit grounding through neutral require a four (4) conductor power supply cord kit rated at 125/250 volts minimum and marked for use with ranges.

See Range Connection Opening Size Chart (Figs. 9 & 10) for cord kit ampere rating information. Terminals on end of wires must be either closed loop or open-end spade lugs with upturned ends.

316454912 specifications

The Frigidaire 316454912 is a highly sought-after oven range component known for its durability and efficient performance. As an integral part of many Frigidaire stove models, this replacement oven igniter ensures that your cooking experience remains seamless and reliable.

One of the main features of the Frigidaire 316454912 is its universal compatibility with a variety of Frigidaire gas ranges. This makes it a versatile choice for users looking to replace a malfunctioning igniter. With dimensions that fit standard connectors, the igniter can be installed easily without requiring extensive modifications or tools, making it a convenient DIY solution for homeowners and cooks.

The Frigidaire 316454912 is designed with advanced technology that enhances its functionality. This igniter is made from high-quality materials that can withstand high temperatures and ensure longevity while providing reliable ignition every time. The component has been rigorously tested to ensure consistent performance—even in demanding cooking conditions—ensuring that your meals are cooked to perfection without the hassle of faulty ignition systems.

Another notable characteristic of the Frigidaire 316454912 is its ability to provide a safe cooking environment. The igniter efficiently ignites the gas burner, reducing the risk of gas build-up, which can lead to hazardous situations. This feature underscores Frigidaire's commitment to safety, making it an essential component in modern kitchen appliances.

The installation process of the Frigidaire 316454912 is user-friendly. Most individuals with basic handyman skills can install the igniter themselves, saving them time and money on professional repairs. Moreover, the overall design of the igniter ensures that it fits snugly within the range, reducing the possibility of leaks and ensuring optimal performance.

In conclusion, the Frigidaire 316454912 is a critical component for anyone looking to maintain or repair their Frigidaire gas range. With its compatibility, advanced safety features, and ease of installation, it stands out as an essential part of kitchen equipment. Whether you're a seasoned chef or a home cook, investing in a quality igniter like the Frigidaire 316454912 ensures that your cooking experience is both enjoyable and efficient.