Frigidaire 318203860 warranty To Operate the Dual Surface Element, Model a

Page 11

Setting Surface Controls

Models with Ceramic Glass Cooktop (continued)

Operating the Dual Surface Radiant Element (Models with Ceramic Glass Cooktop Only)

Model A is equipped with Dual radiant surface elements at all positions (See Figs. 5 & 6). Models B, C, D & E are equipped with a dual radiant surface element located at the right front (See Figs. 7 to 14) position. Symbols on the control panel are used to indicate which coil of the dual radiant element will heat. The symbol indicates that only

the inner coil will heat (Figs. 1, 3, 5, 7, 9, 11 & 13). The

symbol indicates that both inner and outer coils will heat (Figs. 2, 4, 6, 8, 10, 12 & 14). You may switch from either coil setting at any time during cooking.

Small

Element

 

Fig. 1

Smal l

Large

Petit

OFF Grand

hi

hi

6

6

4

4

2

2

l o

l o

Fig. 3

Large

Element

 

Fig. 2

Smal l

Large

Petit

OFF Grand

hi

hi

6

6

4

4

2

2

l o

l o

Fig. 4

To Operate the Dual Surface Element:

1.Place correctly sized cookware on the dual surface element.

2.Push in and turn the control knob counterclockwise (See Fig. 3) for smaller cookware or clockwise (See Fig. 4) for larger cookware.

3.Turn the knob to adjust the setting if needed. Start most cooking operations on a higher setting and then turn to a lower setting to finish cooking. Each surface element provides a constant amount of heat at each setting. A glowing red surface heating area extending beyond the bottom edge of the cookware indicates the cookware is too small for the surface heating area.

4.When cooking has completed, turn the surface control knob to OFF before removing the cookware. Note: The Surface Indicator light will come on when the control knob will be turn on and will continue to glow until the glass cooktop has cooled down to a moderate level. The light may remain on even though the controls are turned OFF.

Note: See page 9, Fig. 1 for recommended control settings.

Radiant surface elements may appear to have cooled after they have been turned off. A hot surface indicator light will come on and will continue to glow until the glass cooktop has cooled down to a moderate level. The glass surface may still be hot and burns may occur if the glass surface is touched before the indicator light has turned off.

Fig. 5 - Model A

Fig. 7 - Model B

Fig. 9 - Model C

Fig. 11 - Model D

Fig. 6 - Model A

Fig. 8 - Model B

Fig. 10 - Model C

Fig. 12 - Model D

11Fig. 13 - Model E

Fig. 14 - Model E

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 28-29 Before Setting Oven Controls 14-1516-17 Before You CallRegister Your Product Welcome & CongratulationsQuestions? SLIDE-IN Models only Important Safety InstructionsKnow which knob controls each surface heating unit Important Instructions for Using Your CooktopAvoid scratching the cooktop glass with sharp objects Important Instructions for Using Your OvenBridge Features At a GlanceDual Models with Coil Surface Elements Setting Surface ControlsSetting Type of Cooking Locations of the Radiant Surface Elements and Controls Models with Ceramic Glass CooktopAbout the Ceramic Glass Cooktop About the Radiant Surface ElementsElectronic surface element control Esec Surface Cooking Settings Models with Ceramic Glass CooktopAvailable Esec Display Settings Recommended Settings for Single, BridgeTo Operate the Single Surface Elements Hot Surface Indicator LightsEsec Error Indicator Message Er Esec Lockout FeatureModel a To Operate the Dual Surface ElementTo Operate the Bridge Surface Element Operating the Bridge Surface Radiant Element Model ETo Set the Warmer Zone Control Warmer Zone Temperature SelectionWarmer Zone Recommended Food Settings Table Food Item Operating the Warmer Warm & Ready Zone Model DCookware Material types Before Setting Oven ControlsSurface cooking Selecting Surface Cooking CookwareRemoving and Replacing Oven Racks Setting Oven ControlsArranging Oven Racks Oven Vent Location -Models with Ceramic Glass CooktopArranging Warmer Warm & Ready Drawer Rack Positions Setting Warmer Drawer Control If EquippedWarmer Drawer Temperature Selection Warmer Drawer Recommended Food Settings Food ItemTo Set the Warmer Drawer Controls Cooking Informations Baking Problems and Solutions ChartDetermining Broiling Times Broiler Clean-Up TipsPreheating To BroilSurfaces How to Clean Care & CleaningCleaning Various Parts of Your Range Cooktop Insert Control Panel Cooktop Cleaning Coil Surface Element Models OnlyCooktop, surface under Porcelain enamel cooktop cleaning instructions some models Cooktop Cleaning- Coil Surface Element Models OnlyCooktop Cleaning Porcelain enamel Cooktop Models For heavy, burned on soil Cleaning Recommendations for the Ceramic Glass CooktopPlastic or foods with a high sugar content For light to moderate soilAluminum utensils Oven CleaningCleaning the Regular Oven non self-clean oven, some models Cleaning the Self-Clean Oven some models Changing Oven Light Removing and Replacing the Oven DoorTo Remove the Hidden Bake Cover some models Storage Drawer some models Adjusting Your Oven TemperatureTo Remove and Replace Warmer Drawer some models Storage Drawer with extendible glides some modelsBefore you call Solutions to Common ProblemsAvoid Transportation Damage to your Range Range Warranty Warranty Information
Top Page Image Contents