GE PB975, PB970 warranty Electrical Connections, Electrical Requirements

Page 4

Installation Instructions

ELECTRICAL CONNECTIONS

ELECTRICAL REQUIREMENTS

CAUTION: For personal safety, do not use an extension cord with this appliance. Remove house fuse or open circuit breaker before beginning installation.

This appliance must be supplied with the proper voltage and frequency, and connected to an individual properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as specified on the rating plate. The rating plate is located on the left hand side of the lower oven front frame.

Location of

model rating plate

We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician. After installation, have the electrician show you where your main range disconnect is located.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your range must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70– Latest Edition. You can get a copy by writing:

National Fire Protection Association

Batterymarch Park

Quincy, MA 02269

Effective January 1, 1996, the National Electrical Code requires that new construction (not existing) utilize a 4-conductor connection to an electric range.

When installing an electric range in new construction, follow Steps 3 and 5 for 4-wire connection.

You must use a 3-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz electrical system.

If the electrical service provided does not meet the above specifications, have a licensed electrician install an approved outlet.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with ring terminals on wire and a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord is not recommended but if used, it should be marked for use with nominal 138diameter connection openings. Care should be taken to center the cable and strain relief within the knockout hole to keep the edge from damaging the cable.

Because range terminals are not accessible after range is in position, flexible service conduit or cord must be used.

NOTE: If conduit is being used, go to Step 3D and then to Step 6 or 7.

On some models, a filter capacitor may be connected between the black and white leads on the junction block.

ALL NEW CONSTRUCTIONS,

MOBILE HOMES AND

INSTALLATIONS WHERE

LOCAL CODES DO NOT

ALLOW GROUNDING

THROUGH NEUTRAL,

REQUIRE A 4-CONDUCTOR

UL-LISTED RANGE CORD.

4

Image 4
Contents For Your Safety Before YOU BeginANTI-TIP Device Read these instructions completely and carefullyPrepare to Install the Range Tools YOU will NeedMaterials YOU MAY Need Parts IncludedPrepare the Opening Electrical Connections Electrical RequirementsPower Cord Strain Relief Installation Do not discard the screwDo not remove the ground strap connection Electrical ConnectionsCut and discard the ground strap. do not Discard ANY Screws Wire Conduit Installation Install the Range Replace the Wire CoverANTI-TIP Device Installation Prepare to Level ModelsOperation Checklist Level the RangePage

PB970, PB975 specifications

The GE PB975 and PB970 are two contemporary offerings from General Electric that exemplify advanced engineering in the realm of electric cooking ranges. These models are designed to cater to the culinary needs of modern households while providing innovative features that enhance cooking efficiency and convenience.

One of the defining features of the GE PB975 and PB970 is their induction cooking technology. Induction cooking utilizes electromagnetic energy to directly heat pots and pans, resulting in faster cooking times compared to traditional gas or electric burners. This technology not only saves time but also enhances energy efficiency, as heat is generated directly in the cookware rather than relying on the heating surface. This characteristic is particularly appealing to environmentally conscious consumers, as it reduces overall energy consumption.

Both models come equipped with various cooking modes, including bake, broil, and warm, allowing users to whip up a diverse array of dishes. The convection feature, present in the PB975, circulates hot air throughout the oven for even cooking results. This ensures that baked goods rise evenly and meats roast to perfection. The user-friendly digital control panel provides precise temperature control and allows for easy programming of cooking times and temperatures.

A standout characteristic of the GE PB975 and PB970 is the built-in self-cleaning feature. This technology employs high temperatures to burn off residues and grease, transforming them into ash that can be easily wiped away. This saves users considerable time and effort in maintaining a clean kitchen.

The design of both ranges is both functional and aesthetically pleasing. The sleek stainless steel finish and modern lines make them a stylish addition to any kitchen. The spacious oven interiors can accommodate large meal preparations, making them suitable for families and entertaining guests.

Safety features like child lock settings and auto shut-off add an extra layer of reassurance for families, ensuring a safer cooking environment. Moreover, the ranges boast easy-to-clean smooth top surfaces that prevent food from sticking and simplify overall maintenance.

In summary, the GE PB975 and PB970 are excellent electric ranges that merge state-of-the-art technology with practical design. With their induction cooking capabilities, convection baking, and user-friendly controls, these models are well-suited for anyone seeking to elevate their culinary experiences. Their combination of style, safety, and efficiency makes them a standout choice in the crowded market of kitchen appliances.