GE 49-85154, 183D5580P236 manual Model and Serial Number Location

Page 28

Installation Instructions

WARNING!

ANTI-TIP DEVICE

To reduce the risk of tipping the range, the range must be secured by a properly installed anti-tip bracket. See installation instructions shipped with the bracket for complete details before attempting to install.

To check if the bracket is installed and engaged properly, carefully tip the range forward. The bracket should stop the range within 4 inches. If it does not, the bracket must be reinstalled. If the range is pulled from the wall for any reason, always repeat this procedure to verify the range is properly secured by the anti-tip bracket.

For free standing or slide in ranges, never completely remove the leveling legs or the range will not be secured to the anti-tip device properly.

If you did not receive an anti-tip bracket with your purchase, call 1.800.626.8774 to receive one at no cost (In Canada, call 1.800.561.3344). For installation instructions of the bracket, visit: GEAppliances.com (In Canada, GEAppliances.ca)

LOCATION

Do not locate the range where it may be subject to strong drafts. Any openings in the floor or wall behind the range should be sealed. Make sure the openings around the base of the range that supply fresh air for combustion and ventilation are not obstructed by carpeting or woodwork.

Your range, like many other household items, is heavy and can settle into soft floor coverings such as cushioned vinyl or carpeting. Use care when moving the range on this type of flooring. It is recommended that the following simple and inexpensive instructions be followed to protect your floor.

The range should be installed on a sheet of plywood (or similar material). When the floor covering ends at the front of the range, the area that the range will rest on should be built up with plywood to the same level or higher than the floor covering.

This will allow the range to be moved for cleaning or servicing. Also, make sure your floor covering will withstand 180°F. (See the Installation Safety Instructions section.)

Make sure the wall coverings around your range can withstand the heat generated (up to 200°F) by the range. (See the Installation Safety Instructions section.)

MODEL AND SERIAL NUMBER LOCATION

Depending on your range, you’ll find the model and serial numbers on a label on the front frame of the range, behind the kick panel or broiler drawer.

IMPORTANT!

Remove all tape and packaging. Make sure the burners are properly seated and level.

Lift up the cooktop (on models with standard twin burners) and remove any packing material under it.

Take the accessory pack out of the oven and/or drawer.

Check to be sure that no range parts have come loose during shipping.

28

Image 28
Contents Installation Instructions Write the model and serial numbers here Model # Serial #Tips Installation Instructions Operating Instructions Consumer Support TroubleshootingSafety Instructions Operating Instructions GEAppliances.comInstructions Cook Meat and Poultry THOROUGHLY… Surface Burners Surface Burners Instructions Operating InstructionsUsing the gas surface burners Support TroubleshootingTips Installation Instructions Operating InstructionsSafety Instructions Instructions TroubleshootingSupport Tips ConsumerTips Installation Using the clock and timerInstructions Operating Instructions Safety Instructions Instructions Installation Using the ovenTips Consumer How to Set the Oven for Baking or Roasting Preheating and Pan PlacementInstructions Operating Aluminum FoilSafety How to Set the Oven for BroilingTips Consumer Support Broiling Guide SuggestionsBroiling Guide CommentsAdjust the oven thermostat-Do it yourself Instructions Troubleshooting Tips Consumer SupportTo Adjust the Thermostat Safety InstructionsCare and cleaning of the range Tips Installation Instructions Operating InstructionsConsumer Support Troubleshooting Standard Twin Burner Assemblies on some modelsBurner Grates Sealed Burner Assemblies on some modelsReplacement Consumer SupportTroubleshooting Tips Consumer Support Cooktop SurfaceDo not use a steel wool pad it will scratch the surface National Parts Center 800.626.2002 U.S CanadaConsumer Support Troubleshooting Tips To clean the inside of the doorTo clean the outside of the door Lift-Off Oven DoorInstructions Operating Broiler Pan and GridRemovable Broiler Drawer on some models Oven Air VentsUsing spray-on oven cleaners Oven RacksTo Clean the Continuous-Cleaning Oven Inthe Commonwealth of Massachusetts Beforeyou BeginToolsyou will Need Foryour SafetyPart Included Materialsyou MAY Need Installation Safety Instructions Dimensions and Clearances Location Model and Serial Number LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Alternate Hookup Gas Flow into RangeFlexible Connector Hookup For models equipped with Standard Twin BurnersElectrical Connections Sealthe Openings Lightthe PilotsElectric Disconnect Light the Surface Burner PilotsAdjust the Surface Burner Pilots if Necessary Light the Oven PilotCheck Ignition of Oven Burner Check Ignition of Surface Burners Standing Pilot ModelsElectric Ignition Models Quality of FlamesLevelthe Range Installthe ANTI-TIP Device⁄ 8 ″ Installthe ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… See the Using the clock and timer section See the Care and cleaning of the range sectionSee the Installation of the range section Oven temperaturePower outage Crackling orPopping sound Rainbow effectOwnership Registration Page Accessories Looking For Something More?Instructions Safety Instructions Consumer Support Troubleshooting Tips InstallationGE Will Replace What GE Will Not CoverSafety Instructions Operating Instructions Troubleshooting Tips Consumer SupportMabe Will Replace What Mabe Will Not CoverConsumer Support U.S. GEAppliances.com