GE 49-85154, 183D5580P236 manual Consumer Support, Replacement

Page 18

Safety Instructions

Care and cleaning of the range.

Burner Caps and Heads (on sealed burners only)

	NOTE: Before removing the burner caps	Replacement
	NOTE: Before removing the burner caps	Replace burner heads over the electrodes
	and heads, remember their size and location.	Replace burner heads over the electrodes
	Replace them in the same location after	on the cooktop, in the correct locations
	cleaning.	according to their size.

Troubleshooting Tips Installation Instructions Operating Instructions

Use a sewing needle or twist-tie

to unclog the small hole in the burner head.

Burner caps

Lift off when cool. Wash burner caps in hot, soapy water and rinse with clean water. You may scour with a plastic scouring pad to remove burned-on food particles.

Burner heads

For proper ignition, make sure the small hole in the section that fits over the electrode is kept open. A sewing needle or wire twist-tie works well to unclog it.

The slits in the burner heads must be kept clean at all times for an even, unhampered flame.

Clogged or dirty burner ports or electrodes will not allow the burner to operate properly.

Any spill on or around an electrode must be carefully cleaned. Take care to not hit an electrode with anything hard or it could be damaged.

You should clean the burner caps and burner heads routinely, especially after bad spillovers, which could clog the openings in the burner heads. Lift off when cool.

To remove burned-on food, soak the burner heads in a solution of mild liquid detergent and hot water for 20–30 minutes. For more stubborn stains, use a toothbrush.

After cleaning

Before putting the burner caps and heads back, shake out excess water and then dry them thoroughly by setting in a warm oven for 30 minutes.

NOTE: Do not use steel wool or scouring powders to clean the burners.

Medium head

Small head

Front of range

Medium head

Large head

Make sure the slot in the burner head is positioned over the electrode.

Replace the matching size caps onto the heads. There is one small, two medium and one large cap. Sizes are stamped into the bottom of the caps.

Medium cap

Small cap

Consumer Support

Front of range

Medium cap

Large cap

Make sure that the heads and caps are replaced in the correct locations.

NOTE: On some models, the burners are all the same size and power.

18

Image 18

Contents Installation Instructions Write the model and serial numbers here Model # Serial #Tips Installation Instructions Operating Instructions Consumer Support TroubleshootingSafety Instructions Operating Instructions GEAppliances.comInstructions Cook Meat and Poultry THOROUGHLY… Surface Burners Surface Burners Instructions Operating InstructionsTips Installation Instructions Operating Using the gas surface burnersSupport Troubleshooting InstructionsSupport Safety InstructionsInstructions Troubleshooting Tips ConsumerUsing the clock and timer Tips InstallationInstructions Operating Instructions Safety Instructions Using the oven Instructions InstallationTips Consumer Instructions Operating How to Set the Oven for Baking or RoastingPreheating and Pan Placement Aluminum FoilTips Consumer Support SafetyHow to Set the Oven for Broiling Broiling Guide SuggestionsBroiling Guide CommentsTo Adjust the Thermostat Adjust the oven thermostat-Do it yourselfInstructions Troubleshooting Tips Consumer Support Safety InstructionsConsumer Support Troubleshooting Care and cleaning of the rangeTips Installation Instructions Operating Instructions Standard Twin Burner Assemblies on some modelsBurner Grates Sealed Burner Assemblies on some modelsReplacement Consumer SupportDo not use a steel wool pad it will scratch the surface Troubleshooting Tips Consumer SupportCooktop Surface National Parts Center 800.626.2002 U.S CanadaTo clean the outside of the door Consumer Support Troubleshooting TipsTo clean the inside of the door Lift-Off Oven DoorRemovable Broiler Drawer on some models Instructions OperatingBroiler Pan and Grid Oven Air VentsUsing spray-on oven cleaners Oven RacksTo Clean the Continuous-Cleaning Oven Inthe Commonwealth of Massachusetts Beforeyou BeginForyour Safety Toolsyou will NeedPart Included Materialsyou MAY Need Installation Safety Instructions Dimensions and Clearances Location Model and Serial Number LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Alternate Hookup Gas Flow into RangeFlexible Connector Hookup For models equipped with Standard Twin BurnersElectrical Connections Electric Disconnect Sealthe OpeningsLightthe Pilots Light the Surface Burner PilotsAdjust the Surface Burner Pilots if Necessary Light the Oven PilotCheck Ignition of Oven Burner Electric Ignition Models Check Ignition of Surface BurnersStanding Pilot Models Quality of FlamesInstallthe ANTI-TIP Device Levelthe Range⁄ 8 ″ Installthe ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… See the Installation of the range section See the Using the clock and timer sectionSee the Care and cleaning of the range section Oven temperaturePopping sound Power outageCrackling or Rainbow effectOwnership Registration Page Accessories Looking For Something More?GE Will Replace Instructions Safety InstructionsConsumer Support Troubleshooting Tips Installation What GE Will Not CoverMabe Will Replace Safety Instructions OperatingInstructions Troubleshooting Tips Consumer Support What Mabe Will Not CoverConsumer Support U.S. GEAppliances.com