GE 164D4290P007, 49-80038 owner manual Cleaning, Surface Units, Drip Pans, Lift-Up Cooktop

Page 21

Be sure the controls are turned to OFF and the surface units are cool before attempting to remove them.

Safety

Surface unit

 

Surface Units

 

 

 

 

 

To clean the surface units, turn the

 

 

 

control to the highest setting for a

 

 

 

minute. The coils will burn off any soil.

 

 

Drip pan

To remove a surface unit:

Receptacle

To remove the drip pans for cleaning,

 

 

 

 

 

 

the surface units must be removed first.

 

 

 

Lift the surface unit about 1″ above

 

 

 

the drip pan and pull it out.

 

 

 

Do not lift the surface unit more than 1. If you

 

 

 

do, it may not lie flat on the drip pan when you

 

 

 

plug it back in.

 

 

 

NOTE: Repeated lifting of the surface unit

 

 

 

more than 1″ above the drip pan can

 

 

 

permanently damage the receptacle.

To replace a surface unit:

Replace the drip pan into the recess in the cooktop. Make sure the opening in the pan lines up with the receptacle.

Insert the terminals of the surface unit through the opening in the drip pan and into the receptacle.

Guide the surface unit into place so it rests evenly.

Do not immerse the surface units in liquids of any kind.

Do not clean the surface units in a dishwasher.

Do not bend the surface unit plug terminals.

Do not attempt to clean, adjust or in any way repair the plug-in receptacle.

Instructions Operating Instructions Care

Drip Pans

Remove the surface units. Then lift out the drip pans.

For best results, clean the drip pans by hand. Place them in a covered container (or a plastic bag) with 1/4 cup ammonia to loosen the soil. Then scrub with a soap-filled scouring pad if necessary. Rinse with clean water and polish with

a clean soft cloth.

The drip pans may also be cleaned in a dishwasher.

Clean the area under the drip pans often. Built-up soil, especially grease, may catch fire.

Do not cover the drip pans with foil. Using foil so close to the receptacle could cause shock, fire or damage to the range.

and Cleaning

Be sure all surface units are turned off before raising the cooktop.

Lift-Up Cooktop

Some models have a cooktop that can be lifted up for easier cleaning. The entire cooktop may be lifted up and supported in the up position.

The surface units do not need to be removed; however, you may remove one to make raising the cooktop easier. There are two side supports that lock into position when the cooktop is lifted up.

After cleaning under the cooktop with hot, mild soapy water and a clean cloth, lower the cooktop. Be careful not to pinch your fingers.

To lower the cooktop, push the rods back and gently lower the cooktop until it rests in place.

Troubleshooting Tips Customer Service

21

Image 21
Contents FC updated RangesSelf-Cleaning ElectricTwo Easy Ways To Register Your Appliance GE & You, a Service PartnershipAll ranges can tip and injury could result Tips Customer ServiceCustomer InstructionsSurface Cooking Units Customer Service Safety InstructionsCleaning Operating Instructions CareSafety Using the surface unitsCleaning Troubleshooting Tips Customer ServiceUsing the oven controls Operating Instructions Safety InstructionsCustomer Service Troubleshooting Tips Care and Cleaning Care and Cleaning Using the ovenSafety How to Set the Oven for BroilingBroiling Guide To BroilCare and Cleaning Using the clock and timerSafety Instructions Using the timed baking and roasting featuresHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopCleaning Troubleshooting Safety InstructionsHow to Set for Regular Baking/Roasting How to Exit the Sabbath FeatureCustomer Service Troubleshooting Tips Care Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat Type of margarine will affect baking performanceUsing the self-cleaning oven Care and Cleaning Troubleshooting Tips Customer ServiceBefore a Clean Cycle Customer Service Troubleshooting Tips Care Cleaning Operating Instructions Safety InstructionsHow to Delay the Start of Cleaning After a Clean CycleCare and cleaning of the range Care and CleaningTroubleshooting Tips Customer Service Instructions Safety Cleaning OperatingInstructions To clean the outside of the door To clean the inside of the doorLift-Off Oven Door To remove the doorTips Care and Cleaning Operating Instructions SafetyOven Light Replacement Broiler Pan & GridSurface Units CleaningDrip Pans Lift-Up CooktopBefore You Call For Service… Power outage Oven temperatureDuring a clean cycle Not unlock Oven not clean afterClean light is on Clean light flashesOn when range is not Oven makesWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Care and Cleaning Troubleshooting Tips Customer Service GE Electric Range WarrantySafety Instructions Operating GE Will ProvideGE Answer Center Service Telephone Numbers

164D4290P007, 49-80038 specifications

The GE 49-80038,164D4290P007 is an advanced circuit breaker designed for industrial applications, providing robust protection and control in electrical distribution systems. This model is engineered by General Electric, a leading name in the field of energy management and electrical solutions. It exemplifies innovation, reliability, and efficiency, tailored for demanding environments.

One of the standout features of the GE 49-80038 is its high breaking capacity, which allows it to interrupt fault currents effectively. This feature is crucial for ensuring the safety of electrical systems as it reduces the risk of equipment damage and fire hazards. The circuit breaker also offers a range of current ratings, allowing it to be used in diverse applications while ensuring optimal performance.

A notable technology integrated into the GE 49-80038 is its electronic trip system. This technology enhances the breaker's ability to detect overloads and short circuits, enabling precise trip settings and minimizing nuisance tripping. The electronic trip unit is customizable, allowing users to set the desired protection levels according to their specific needs, thus increasing operational flexibility.

In terms of design, the GE 49-80038 is built for easy installation and maintenance. Its compact form factor allows it to fit into standard electrical panels without requiring excessive modifications. Furthermore, the device includes features for remote monitoring and control, integrating seamlessly into modern smart grid applications.

Durability is another hallmark of this circuit breaker. Constructed from high-quality materials, the GE 49-80038 can withstand harsh environmental conditions, including high temperatures and humidity levels. This resilience ensures a long service life, reducing the frequency and costs associated with replacements.

Additionally, the circuit breaker complies with international standards, making it suitable for installation in various regions without the need for modifications. This compliance ensures reliability and performance across different electrical systems globally.

In summary, the GE 49-80038,164D4290P007 represents a cutting-edge solution for circuit protection in industrial settings, featuring high breaking capacity, an advanced electronic trip system, ease of installation, and unmatched durability. Its blend of innovative technologies and robust characteristics makes it a favorite choice for electrical professionals looking to enhance the safety and efficiency of their systems.