Stanley Black & Decker GT18B01 Programmable Controller, Troubleshooting Guidelines, Fault Codes

Page 15

PROGRAMMABLE CONTROLLER

The Stanley programmable controller is an electronic engine governor that provides a means of controlling and limiting engine speed by adjusting the fuel control lever with a proportional actuator.

The controller is factory preset and has no manual adjust- ments.

A flashing LED indicates the fault condition

TROUBLESHOOTING GUIDELINES

Please follow the checklist below to troubleshoot your Stan- ley controller.

1.Check battery voltage for stability and correct value. The LED will turn on for one second when the controller 4500 is first powered up.

2.Check the actuator linkage for binding and backlash.

Checking Performance Control™ (Electronic Governor-Static Check)

To determine whether a governor problem is being caused by the actuator or the control module, perform the following static check exactly in order shown.

A pair of jumper wires and a known good 12-volt battery is required.

1.Disconnect red and green wires from the control module to actuator.

2.Attach jumper wires from battery to RED and GREEN wires to actuator.

a.Attach 12 volt + (positive) to RED wire.

b.Attach 12 volt – (negative) to GREEN wire.

3.Actuator should move throttle lever to wide open position.

a. If actuator does not move it is defective. (Replace). b. If actuator moves throttle to wide-open position, the module is defective. (Replace).

FAULT CODES

The Stanley controller is capable of identifying certain fault conditions and alerting the user to them. A flashing LED indicates the fault conditions. The current fault code list is shown on the following page. Please note the following:

1.When power is first applied to the controller, the LED will flash just once for one second to indicate that the LED is working.

2.If there are multiple faults, the LED will flash them all

in sequence. Count the flash codes to determine the fault conditions or connect the Calibration Tool to observe the fault conditions. (Use the “Display Faults” option under the Monitor Menu.)

3.If there are no faults, the LED will flash once at reset and from then on indicate the detection of engine speed. A continuous ON LED indicates that a valid engine speed is being sensed.

4.The controller will attempt to shut down for some faults and will not permit starting after reset with faults 1, 5 and 8.

GT18B01-B02 User Manual ◄ 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents GT18B01 GT18B02 Weisbeck, Andy Declarationrtificate OfofconformityTable of Contents Local Safety Regulations Safety SymbolsSafety Precautions Tool Stickers & Tags TAG Shown below is Attached to Conductive Hose Hose TypesTool to Hydraulic Circuit Hose Recommendations Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsPreparation for USE OperationBattery Quick Disconnect CouplersTool For 8 GPM Operation ControlsStartup For 5 GPM OperationShutdown Cold Weather StartupSpark Plug Routine MaintenanceEngine Maintenance Hydraulic System MaintenanceTroubleshooting Guidelines Fault CodesProgrammable Controller Flash Engine Code Fault Shutdown Corrective Action Fault CodesTesting & Troubleshooting Testing the Hydraulic CircuitGeneral Troubleshootong Problem Cause RemedySpecifications GT18B01 & B02 Parts Illustration GT18B01 & B02 Parts List MIX OLD Style Tank and CAP with NEW Style Tank and CAP Fuel Tank & CAPFrame Parts HOSES, Fittings & Clamps Harness Part Number Main Wiring Harness

GT18B01, GT18B02 specifications

The Stanley Black & Decker GT18B02 and GT18B01 models represent a significant advancement in the realm of outdoor power equipment, specifically designed for homeowners and gardening enthusiasts seeking efficient solutions for lawn maintenance and landscaping tasks. These tools are particularly notable for their commitment to performance, ease of use, and innovative technology, making them stand out in a competitive market.

One of the key features of both models is their powerful electric motor, providing ample torque and speed to tackle various cutting tasks. The GT18B02 is equipped with a robust brushless motor that extends the tool's life and enhances battery efficiency, reducing the need for frequent recharging. This is complemented by a high-capacity battery that offers several hours of continuous operation, perfect for larger gardens or extensive landscaping projects.

Both models feature a lightweight yet durable design, ensuring maneuverability without compromising on strength. This ergonomic approach allows users to navigate tight spaces and awkward angles with ease, making lawn edging and trimming less of a chore. The adjustable shaft length is another significant characteristic, catering to users of different heights and providing comfort during prolonged use.

The GT18B02 and GT18B01 are equipped with a dual-line cutting system, which allows for a wider cutting swath, significantly reducing the time spent on tasks. The automatic feed spool ensures that the line is always at the optimal length for efficient cutting, eliminating the hassle of manual adjustments. Additionally, these models incorporate a protective shield to enhance safety and reduce debris flight during operation.

In terms of technology, both models feature a smart LED indicator that provides real-time battery status updates, ensuring users are never caught off guard by a dying battery. Furthermore, they boast quick charge capabilities, allowing the battery to return to full power faster, ready for the next job.

In summary, the Stanley Black & Decker GT18B02 and GT18B01 are comprehensive solutions for anyone looking to streamline their lawn maintenance routines. With powerful motors, ergonomic designs, efficient cutting systems, and smart technology integration, these models promise to enhance productivity and make outdoor tasks more manageable. Whether you’re maintaining a small garden or tackling larger landscaping jobs, these trimmers deliver the performance and convenience needed to achieve professional results.
Top Page Image Contents