Stanley Black & Decker GT18B01 Hose Types, TAG Shown below is Attached to Conductive Hose

Page 7

HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

 

A G

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

T

 

 

 

 

 

 

 

 

 

 

I S

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

3.

DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

H

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

T

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

VE

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

O

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

 

 

 

 

ELECTRIC LINES.

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

E

 

 

 

 

 

 

 

 

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

R

 

 

 

 

 

 

 

 

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

T

 

 

 

 

 

 

 

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

N O

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

6.

 

D O

 

 

 

 

 

 

 

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

 

SIDE 1

 

 

 

 

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

 

 

TRIC LINES.

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

SEE OTHER SIDE

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

SIDE 1

 

 

SIDE 2

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

GT18B01-B02 User Manual ◄ 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents GT18B01 GT18B02 Weisbeck, Andy Declarationrtificate OfofconformityTable of Contents Local Safety Regulations Safety SymbolsSafety Precautions Tool Stickers & Tags TAG Shown below is Attached to Conductive Hose Hose TypesTool to Hydraulic Circuit Hose Recommendations Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsPreparation for USE OperationQuick Disconnect Couplers BatteryTool For 8 GPM Operation ControlsStartup For 5 GPM OperationShutdown Cold Weather StartupSpark Plug Routine MaintenanceEngine Maintenance Hydraulic System MaintenanceFault Codes Troubleshooting GuidelinesProgrammable Controller Flash Engine Code Fault Shutdown Corrective Action Fault CodesTesting the Hydraulic Circuit Testing & TroubleshootingGeneral Troubleshootong Problem Cause RemedySpecifications GT18B01 & B02 Parts Illustration GT18B01 & B02 Parts List MIX OLD Style Tank and CAP with NEW Style Tank and CAP Fuel Tank & CAPFrame Parts HOSES, Fittings & Clamps Harness Part Number Main Wiring Harness

GT18B01, GT18B02 specifications

The Stanley Black & Decker GT18B02 and GT18B01 models represent a significant advancement in the realm of outdoor power equipment, specifically designed for homeowners and gardening enthusiasts seeking efficient solutions for lawn maintenance and landscaping tasks. These tools are particularly notable for their commitment to performance, ease of use, and innovative technology, making them stand out in a competitive market.

One of the key features of both models is their powerful electric motor, providing ample torque and speed to tackle various cutting tasks. The GT18B02 is equipped with a robust brushless motor that extends the tool's life and enhances battery efficiency, reducing the need for frequent recharging. This is complemented by a high-capacity battery that offers several hours of continuous operation, perfect for larger gardens or extensive landscaping projects.

Both models feature a lightweight yet durable design, ensuring maneuverability without compromising on strength. This ergonomic approach allows users to navigate tight spaces and awkward angles with ease, making lawn edging and trimming less of a chore. The adjustable shaft length is another significant characteristic, catering to users of different heights and providing comfort during prolonged use.

The GT18B02 and GT18B01 are equipped with a dual-line cutting system, which allows for a wider cutting swath, significantly reducing the time spent on tasks. The automatic feed spool ensures that the line is always at the optimal length for efficient cutting, eliminating the hassle of manual adjustments. Additionally, these models incorporate a protective shield to enhance safety and reduce debris flight during operation.

In terms of technology, both models feature a smart LED indicator that provides real-time battery status updates, ensuring users are never caught off guard by a dying battery. Furthermore, they boast quick charge capabilities, allowing the battery to return to full power faster, ready for the next job.

In summary, the Stanley Black & Decker GT18B02 and GT18B01 are comprehensive solutions for anyone looking to streamline their lawn maintenance routines. With powerful motors, ergonomic designs, efficient cutting systems, and smart technology integration, these models promise to enhance productivity and make outdoor tasks more manageable. Whether you’re maintaining a small garden or tackling larger landscaping jobs, these trimmers deliver the performance and convenience needed to achieve professional results.
Top Page Image Contents