Stow SFG10E manual Lubrication Points, Lubrication Requirements

Page 34

CAUTION

Do not install an elastomeric mount without the use of an approved lubricant. Installation without an approved lubricant can produce tears in the mount, resulting in substandard operational performance and service life.

9)Support the elastomeric mount, socket and mounting plate as depicted in FIGURE 50. The mounting plate must be suspended from the arbor press to allow the mount to clear when the pressing process is completed. A short section of 1-1/2 inch inside diameter steel tubing can be utilized for this purpose. Using the arbor press, apply a steady force in a straight line direction to the mount until it fully penetrates the cavity in the mounting disc. Do not attempt to push the elastomeric mount through the mounting disc with excessive force. Damage to the elastomeric mount will result.

10)Reassemble the mounting disc to the transmission shaft.

11)Reassemble the mounting plate to the mounting disc.

12)Reassemble the aluminum multi-accessory disc to the mounting plate.

13)Check to determine that the replacement elastomeric mounts allow for proper position of the aluminum multi- accessory disc. If the elastomeric mounts are not properly positioned, they will require removal and reinstallation. The removal process can produce tears and abrasions in the mount that will require new replacements.

MAINTENANCE/SERVICE

LUBRICATION REQUIREMENTS

Parts Required:

1 each, standard grease gun filled with one of the following: ESSO Beacon 325, Shell Alvania #2, Chevron SRI, or equivalent.

1 each, container of dry film lubricant.

1)Lubricate the caster wheel bearings with a dry film lubricant only. Dry film lubricants dry immediately upon contact. Use sparingly. Excess lubricant will attract the fine grained, powdered materials described and directly affect bearing service life.

CAUTION

Do not lubricate the caster wheels with any type of grease material. Grease will attract foreign material accumulations that can accelerate bearing wear.

2)The transmission gears are supported by extra capacity, ball bearing units. Bearings are lubricated at the time of manufacture and do not require additional servicing when placing the unit in initial service. Zerk grease fittings can promote improper service schedules and an excessive amount of over lubrication. Excess grease escaping from around the bearing insert seals will attract foreign material accumulations that can drastically shorten their service life. Excessive amounts of grease in the bearing race cavity can actually increase friction and resulting heat increases that can also dramatically shorten bearing service life.

FIGURE 50

FIGURE 51. LUBRICATION POINTS

SFG10E ELECTRIC SURFACE GRINDER — OPERATION AND PARTS MANUAL — REV. #1 (07/16/07) — PAGE 34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model SFG10E SILICOSIS/RESPIRATORYWARNINGS Table of Contents Parts Ordering Procedures Stow Construction Equipment’ASSISTANCE Appropriee Avant D’UTILISER LE Produit Page Operator Instructional Data Sheet Safety Precautions Safety Precautions Operation MAINTENANCE, Repair and Storage Assembly Removing the Surface Grinder from the PalletTheory of Operation MULTI-ACCESSORY Attachments and ApplicationsGrinding Stones Scarifier Blocks Tungsten Carbide Grinding BlockStar Flail Beam Flail Pentagonal FlailSpacerWasher Scarifier Block BushingFloor Brushes Wire brushesSCRAPE-R-TACH Industrial Floor Coatings Removal System Follow all safety precautions for the safety solvent Multi-Segmented, Dry Diamond Disc Diamond Segment Block Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Adjustingthe Operator Handle Height Starting the SFG10E Surface Grinder on the JobsiteAssembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Assembly INSTRUCTIONS/OPERATIONS Page Early Age Grinding Stoppingthe SFG10E Surface GrinderDefinitions of floor flatness and levelness How to Define Surface Regularity Defined Versus RandomTraffic PatternsTR 34 tolerances for defined traffic floors Preventative Maintenance Check List Observe all applicable safety precautions for the solventMAINTENANCE/SERVICE Installing a Replacement V-BELT or PulleyMAINTENANCE/SERVICE Lubrication Points Lubrication RequirementsElectric Motor Service ACCELERATEDV-BELTWEAR Operational ProblemsElectric Motor Uneven Grinding ActionStorage Specifications Page Part Name RemarksSuggested Spare Parts Qty DescriptionOperator Handle Assy Operator Handle AssySwitch COVER, SwitchMOUNT, Rubber SFWS277 ASSEMBLY, Swivel CAM, SwitchElectric Motor Assy Electric Motor AssyPulley MOTOR, ELECTRIC, 1-1/2 HP, 115 VACMOUNT, Electric Motor Included with ItemWheel Dolly Assy Wheel Dolly AssySCRAPER, Wheel ARM, SwingWheel WASHER, FLAT, 3/4, PlatedFrame Assy Frame AssyCONNECTOR, GREASE, 1/4-28 UNF WeightDISC, MULTI-ACCESSORY, LH CONNECTOR, GREASE, 1/8 PipeSafety and Dust Shield Assy Safety and Dust Shield AssyHOSE, Vacuum Skirt AssyBUMPER, Rubber STRAP, SkirtScarifier Assy Scarifier AssySee Note HousingBushing NUT, HEX 3/8 UNC, Nylock PlatedSCRAPE-R-TACH Assy SCRAPE-R-TACH AssyINSERT, Tungsten Carbide HOLDER, InsertSpacer NUT, Nylock 5/16-1/8 UNC, PlatedGrinding Block Assy Grinding Block AssyWedge Plastic BlockRing Aggress GrindingDecals DecalsDECAL, Motor START/STOP Sfdclsdp DECAL, Stow Large DECAL, WarningDECAL, Grease Bearings DECAL, Warning SFSP8E5HP5020Payment Terms Special Expediting ServicePRICING, Rebates Specifications Freight PolicyPage Heres HOW to GET Help Parts Department
Top Page Image Contents