Multiquip MVH408GH manual Cast iron construction used in the compacting of soil

Page 15

COMPONENTS

Figure 2 shows the location of the basic controls and components of the MVH408GH Plate Compactor. The function of each control is described below:

1.Rubber Cover — Lift this rubber cover to gain access to the fuel tank.

2.Hour/Tachometer — Displays the cumulative time that the machine has been in use. During operation it displays the rpm reading.

3.Handle Bar Height Adjuster — Adjusts the the handle bar to the desired height by loosening the wing nut and turning the grip clockwise to raise the handle bar and counterclockwise to lower the handle bar.

4.Breather Plug — Allow pressure to escape to the air in the form of a gas from heat.

5.Hydraulic Pump (Oil Reservoir) — Regulates hydraulic oil flow produced by the direction of the control lever.

6.Hand Grip — When operating the compactor use this hand grip to maneuver the compactor.

7.Cyclone Cleaner — Filters large dust particles to keep air cleaner from getting clogged easily.

8.Lifting Bale — When lifting of the compactor is required either by forklift, crane etc., tie rope or chain around this lifting point.

9.Vibrating Plate — A flat, open plate made of durable

cast iron construction used in the compacting of soil.

10.Extension Plate — Provides additional area of vibration to the vibrating plate.

11.Handle Bar — When operating the compactor, this handle is to be in the downward position. When the compactor is to be stored, move the handle bar to the upright position.

12.Direction Control Lever Push the lever forward to move compactor in a forward direction. Pull the lever backwards to move compactor in backwards direction. Placing the lever in the middle (midway) will cause the compactor not to move (neutral).

13.Throttle Lever Controls speed of the plate compactor. Place straight vertically to start, push fully counterclockwise for full throttle and fully clockwise to stop plate compactor.

14.Vibrator Oil Drain Plug — Used to drain vibrator oil from the machine.

15.Vibration Case Oil Filler — Used to add oil to the vibration case.

16.Engine—ThisplatecompactorusesaGX390UT2SMXC gasoline engine. Refer to the owner’s manual for engine information.

17.Engine ON-OFF Switch — Used to turn the engine on or off.

MVH408GH PLATE COMPACTOR • OPERATION AND PARTS MANUAL — REV. #0 (03/25/14)— PAGE 15

Image 15
Contents This Manual Must Accompany the Equipment AT ALL Times Model MVH408GHProposition 65 Warning Page MVH408GH Reversible Plate Compactor Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresSafety Messages Safety InformationGeneral Safety Compactor Safety Engine SafetyBefore servicing equipment Fuel Safety Battery Safety Electric Start only Use well-insulated gloves when picking up the battery Emissions Information Transporting SafetyHonda SpecificationsCentrifugal Force 12,365 lbf 55 kN Engine Make19.68 25.60 36.61 47.64 53.54 35.3 62.01 DimensionsGeneral Information Plate Compactor Components ComponentsCast iron construction used in the compacting of soil Initial Servicing Basic EngineFuel Check InspectionBefore Starting Engine OIL CheckHandle BAR Belt InspectionBelt Tension Vibrator OIL CheckPlace the engine ON/OFF switch in the on position StartupStarting the Engine Open Do not pull the starter rope all the way to the endNever stop the engine suddenly while working at high speeds OperationOperation Stopping the EnginePlace the fuel shut-off lever in the OFF position Place the engine ON/OFF switch in the OFF positionGeneral Maintenance MaintenancePerform engine maintance as listed in Table Engine MaintenancePerform machine inspection as listed in Table Engine AIR CleanerMachine Inspection Tightening TorqueCyclone Cleaner Engine OILUnlatch and remove dust pot Figure Case the air bleeding is insufficient, repeat steps 9 Hydraulic OILSpark Arrester Cleaning Spark PlugBelt Storage Troubleshooting Compactor Troubleshooting Engine Troubleshooting EngineAir cleaner dirty? Clean or replace air cleaner Page Sample Parts List Explanation of Code in Remarks ColumnXxxxx only Not Used on Suggested Spare Parts Vibrating Plate Assy Packing 1/4 CU Vibrating PlateOIL Gauge Copper PackingVibrator Assy GEAR, Drive Connector PT, PF1/4Roller Bearing NJ310EMC4 Rotary SHAFT, DriveBase and Engine Assy Socket Head Bolt 10X25 T Base L100Engine ASSY., GX390UT2SMXC Belt COVER,Base and Engine Assy Rubber COVER, Upper WASHER, Flat M14Center Cover NUT M14Electric Device Assy Wire HARNESS/MRH-600 Wiring Fixed BaseStop SWITCH,ENGINE Lead Wire SW-GROUNDControl Assy Rubber Coupling Handle Bracket RHandle Bracket L WASHER, Flat M12Control Assy Travel Lever OIL HoseBreather CAP Spiral TubeNameplate and Decals Assy Nameplate and Decals Assy Honda GX390UT2SMXC Cylinder Head Assy GASKET, Cylinder Head GUIDE, IN. Valve OversizeGUIDE, EX. Valve Oversize CLIP, Valve GuideHonda GX390UT2SMXC Cylinder Barrel Assy OIL Seal Switch ASSY., OIL LevelSHAFT, Governor ARM BOLT, Drain PlugHonda GX390UT2SMXC Crankcase Cover Assy PACKING, OIL Filler CAP WEIGHT, GovernorHOLDER, Governor Weight PIN, Governor WeightHonda GX390UT2SMXC Crankshaft Assy KEY 7X7X33 Yellow WEIGHT, BalancerBolt WASHER, Lock 8MMHonda GX390UT2SMXC Piston Assy Piston STD BOLT, Connecting RODRing SET, Piston STD Ring SET, PistonHonda GX390UT2SMXC Camshaft Assy ROD, Push NUT, Pivot AdjustingSEAL, Valve Stem Camshaft AssyHonda GX390UT2SMXC Recoil Starter Assy Spring Friction Case CP, Recoil Starter Includes Items W/ #PULLEY, Recoil Starter RATCHET, StarterHonda GX390UT2SMXC FAN Cover Assy GROMMET, Drain Hole CLIP, TubeCover CP, FAN/BLACK ShroudHonda GX390UT2SMXC Carburetor Assy Screw SET Pilot PLATE, Lever SettingGasket SET Valve SET, FloatHonda GX390UT2SMXC AIR Cleaner Assy Collar B, AIR Cleaner Cover CP, AIR CleanerGROMMET, AIR Cleaner COLLAR, AIR CleanerHonda GX390UT2SMXC Muffler Assy CAP, Muffler Muffler CompPROTECTOR, Exhaust Pipe PIPE, ExhaustHonda GX390UT2SMXC Fuel Tank Assy CLAMP, Tube D8 RUBBER, Support 107MMJOINT, Fuel Tank Tank CP, FUEL/BLACKHonda GX390UT2SMXC Flywheel Assy NUT, Special 16MM FAN, CoolingPULLEY, Starter Flywheel CompHonda GX390UT2SMXC Ignition Coil Assy Coil ASSY. Ignition Harness ASSY. Engine WireGROMMET, Cord CLIP, HarnessHonda GX390UT2SMXC Control Assy ROD, Governor Adjusting SpringHOLDER, Wire ARM, GovernorHonda GX390UT2SMXC Engine Decal Assy WRENCH, Spark Plug MARK, AIR CleanerMARK, Choke Gray MARK, Throttle IndicationFreight Policy Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help

MVH408GH specifications

The Multiquip MVH408GH is a powerful and versatile piece of equipment designed for professionals in the construction and landscaping industries. This robust vibratory plate compactor is engineered to deliver high performance while ensuring operator comfort and ease of use. With its advanced features and technology, the MVH408GH stands out as an essential tool for compacting soil, gravel, and asphalt.

One of the key features of the MVH408GH is its Honda GX160 engine. This reliable, air-cooled, 4-stroke engine offers excellent fuel efficiency and low emissions, making it an environmentally friendly option. The engine delivers a maximum power output, ensuring that the compactor can handle even the toughest jobs with ease. Thanks to its high-performance engine, the MVH408GH can achieve an impressively high compaction force, making it suitable for a wide range of applications.

The compactor is equipped with a heavy-duty, solid steel base plate, designed to withstand the rigors of frequent use. The base plate measures 22 inches wide, providing a large effective surface area that maximizes compaction efficiency. Additionally, the design of the plate helps to reduce vibration transmitted to the operator, enhancing comfort during prolonged operation.

Another significant feature of the MVH408GH is its easy maneuverability. The compactor features a lightweight design that allows operators to transport and position it effortlessly. It also comes with a foldable handle, which not only allows for compact storage but also provides convenient lifting and carrying options.

The technologically advanced vibration system in the MVH408GH helps to achieve superior compaction results. The system is precisely engineered to produce a high-frequency vibration, which aids in the densification of material during the compaction process. This results in optimal performance, enabling operators to complete their tasks more efficiently.

Safety is also a priority in the design of the MVH408GH. The compactor features a protective frame that shields the engine and other critical components from potential damage on the job site. Additionally, it is equipped with convenient controls that are easy to access, promoting safe and straightforward operation.

In summary, the Multiquip MVH408GH is a top-tier vibratory plate compactor characterized by its powerful Honda engine, robust construction, high compaction efficiency, and user-friendly design. The combination of these features makes it an ideal choice for construction professionals seeking reliability and performance in their compaction equipment.