Sharp R-930AW service manual Servicing

Page 28

R-930AK

R-930AW

SERVICING

1.Precautions for Handling Electronic Components This unit uses CMOS LSI in the integral part of the circuits. When handling these parts, the following precautions should be strictly followed. CMOS LSI have extremely high impedance at its input and output terminals. For this reason, it is easily influenced by the surrounding high voltage power source, static electricity charge in clothes, etc, and sometimes it is not fully protected by the built-in protection circuit.

In order to protect CMOS LSI.

1)When storing and transporting, thoroughly wrap them in aluminium foil. Also wrap all PW boards containing them in aluminium foil.

2)When soldering, ground the technician as shown in the figure and use grounded soldering iron and work table.

approx. 1M ohm

2. Shapes of Electronic Components

C B

 

 

Transistor

 

 

DTA123ES

E

 

 

KRA101M

Transistor

 

 

E

C B

KRA223M

2SB910M

 

KRC243M

3.Servicing of Touch Control Panel

We describe the procedures to permit servicing of the touch control panel of the microwave oven and the precautions you must take when doing so. To perform the servicing, power to the touch control panel is available either from the power line of the oven itself or from an external power source.

(1)Servicing the touch control panel with power supply of the oven:

CAUTION:

THE HIGH VOLTAGE TRANSFORMER OF THE MICROWAVE OVEN IS STILL LIVE DURING SERVICING PRESENTS A HAZARD.

Therefore, when checking the performance of the touch control panel, put the outer cabinet on the oven to avoid touching the high voltage transformer, or unplug the primary terminal (connector) of the high voltage transformer to turn it off; the end of such connector must be insulated with an insulating tape. After servicing, be sure to replace the leads to their original locations.

A. On some models, the power supply cord between the touch control panel and the oven itself is so short that the two can't be separated.

For those models, check and repair all the controls (sensor-related ones included) of the touch control panel

while keeping it connected to the oven.

B.On some models, the power supply cord between the touch control panel and the oven proper is long enough that they may be separated from each other. For those models, therefore, it is possible to check and repair the controls of the touch control panel while keeping it apart from the oven proper; in this case you must short both ends of the door sensing switch (on PWB) of the touch control panel with a jumper, which brings about an operational state that is equivalent to the oven door being closed. As for the sensor-related controls of the touch control panel, checking them is possible if dummy resistor(s) with resistance equal to that of the controls are used.

(2)Servicing the touch control panel with power supply from an external power source:

Disconnect the touch control panel completely from the oven proper,and short both ends of the door sensing switch (on PWB) of the touch control panel,which brings about an operational state that is equivalent to the oven door being closed. Connect an external power source to the power input terminal of the touch control panel, then it is possible to check and repair the controls of the touch control panel it is also possible to check the sensor- related controls of the touch control panel by using the dummy resistor(s).

4.Servicing Tools

Tools required to service the touch control panel assembly.

1)Soldering iron: 30W

(It is recommended to use a soldering iron with a grounding terminal.)

2)Oscilloscope: Single beam, frequency range: DC - 10MHz type or more advanced model.

3)Others: Hand tools

5. Other Precautions

1)Before turning on the power source of the control unit, remove the aluminum foil applied for preventing static electricity.

2)Connect the connector of the key unit to the control unit being sure that the lead wires are not twisted.

3)After aluminum foil is removed, be careful that abnormal voltage due to static electricity etc. is not applied to the input or output terminals.

4)Attach connectors, electrolytic capacitors, etc. to PWB, making sure that all connections are tight.

5)Be sure to use specified components where high precision is required.

26

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Table of Contents Convection Microwave Oven930AK 930AW Before Servicing Requirements Microwave Measurement ProcedureLeakage test Sharp PLAZA, Mahwah Convection Microwave Oven930AK / R-930AW ForewordSpecification General InformationDescription Grounding InstructionsOven Diagram Touch Control PanelPower Level P-0 to P-90 Cooking OperationDescription of Operating Sequence OFF ConditionConvection Cooking Condition Automatic MIX Cooking ConditionSensor Cooking Condition Preheating ConditionFire Sensing Feature Microwave Mode Compu BROIL/ Compu ROAST/ Compu BakeCompu Defrost Cooking Cooking SequenceSchematic Diagram Figure O-1. Oven Schematic-OFF ConditionFigure O-4. Oven Schematic-Convection Cooking Condition Description and Function of Components Troubleshooting Guide Heating ElementConvection Cooking System Damper OPEN-CLOSE MechanismTest Procedure Problem Possible Cause Defective PartsTest Procedures Procedure Component Test Letter Magnetron Assembly TestPower Transformer Test High Voltage Rectifier TestProcedure Component Test Letter Secondary Interlock Switch TestMonitor Switch Temperature Fuse TestTest Procedures Component Test Letter Damper Switch TestChecking Temperature in the Convection Mode Thermal CUT-OUT TestTouch Control Panel Assembly Test Outer Case Switch TestKEY Unit Test Relay Test Weight 1ST Stage 2ND Stage 3RD Stage 4TH Stage Level TimeCompu Defrost Test Occurrence Cause or Correction AH Sensor TestChecking the initial sensor cooking condition Water load cooking testTest Procedures Letter Component Test Testing Method for AH Sensor AND/OR Control UnitChecking Control Unit R1,R2 22Ω ± R3 4.3kΩ ± 5% 1/4WTouch Control Panel Assembly ThermistorDescription of LSI LSIIZA797DRTOR Signal similar to P27 Segment data signalsSegment data signal Key strobe signalAbsolute Humidity Sensor Circuit Structure of Absolute Humidity SensorServicing Component Replacement and Adjustment Procedure Outer Case Switches ReplacementPower Transformer Removal Outer Case RemovalHigh Voltage Rectifier Assembly Removal Positive Lock Connector NO-CASE Type RemovalMagnetron Removal High Voltage Capacitor RemovalDamper Assembly Removal Turntable Motor RemovalOven Lamp and Lamp Socket Removal FAN Motor RemovalControl Panel Assembly and Control Unit Removal Control Unit and KEY UnitDoor Replacement and Adjustment After adjustment, check the followingDoor Adjustment After adjustment, make sure of the followingDoor Disassembly Figure C-5. Door Replacement and adjustmentFigure S-1. Pictorial Diagram Circuit Control PanelDIP Cabinet Parts Electrical PartsControl Panel Parts Oven Parts VSDTA123ES/-3Miscellaneous Door PartsScrews Nuts and Washers HOW to Order Replacement Parts Packing and AccessoriesModel Number DescriptionOven Control Panel Parts Door Parts Miscellaneous 930AK 930AW
Related manuals
Manual 32 pages 15.53 Kb

R-930AW specifications

The Sharp R-930 series of microwave ovens, including the R-930AK, R-930AW, and R-930CS models, represent a blend of advanced technology and user-centric design. These units are well-suited for modern kitchens, offering convenience, versatility, and efficiency that meet the needs of busy households.

One of the standout features of the R-930 series is the powerful Inverter Technology. Unlike traditional microwaves that rely on pulsing power to cook food at lower settings, Inverter Technology delivers a steady stream of cooking power. This results in more even heating, improved texture, and better overall cooking results for delicate dishes like custards and sauces.

The spacious interior of these models provides ample room for cooking a variety of dishes simultaneously. The R-930 series is designed with a turntable that ensures uniform cooking by rotating food as it heats. Additionally, these microwaves often come with a variety of pre-programmed settings for popular dishes, making it easier for users to prepare meals with minimal effort. These presets take the guesswork out of cooking and help ensure consistent results every time.

The R-930AK and R-930AW models are particularly noted for their sleek and modern aesthetic, available in stylish black and white exteriors, respectively. Both models also feature user-friendly controls, which include a digital display and intuitive buttons, ensuring that even those new to microwave cooking can navigate settings with ease.

Another characteristic that distinguishes the R-930CS is its advanced sensor cooking technology. This feature monitors the cooking process and automatically adjusts power levels and cooking times to achieve optimal results. This takes the hassle out of determining how long to cook various foods, especially those that require specific attention to avoid overcooking or undercooking.

The Sharp R-930 series also emphasizes safety and convenience. Child safety locks are integrated into the design to prevent unauthorized use, making it a practical choice for families with young children. Moreover, the easy-clean interior ensures that spills and splatters can be quickly wiped away, maintaining hygiene and preserving the appliance's appearance.

In summary, the Sharp R-930AK, R-930AW, and R-930CS models are proficient microwave ovens equipped with innovative technologies and thoughtful features that cater to a variety of cooking needs. With their combination of inverter cooking technology, spacious interiors, sleek designs, and user-friendly controls, these models are ideal choices for anyone looking to enhance their culinary capabilities in a fast-paced world.
Top Page Image Contents