Gemini MM-4000 manual Effects

MM-4000

CONTROLS: (CONTINUED) CONTROLS: (CONTINUED)

14	3 BAND EQUALIZER
	The 3 BAND EQUALIZER adjust the tone of each CHANNEL by
	giving you a choice 3 frequencies (BANDS) to adjust , from LOW,
	MIDRANGE (MID) and HIGH’s ,you can use the adjustment knobs to
	higher or lower the 3 separate frequencies till the sound of the music
	program is appropriate for your listening environment.
15	EFFECT ASSIGN
	The EFFECT ASSIGN buttons allow you to choose which channel

(LINE or MIC) will be sent to the effects section, either one or all channels can be selected at once (see effects section).

25 ZONE VOLUME ROTARY

Controls the volume level of the ZONE OUTPUT .

26 MASTER VOLUME ROTARY

The MASTER VOLUME ROTARY knob adjust the volume of the

MAIN OUTPUT.

27 CUE VOLUME ROTARY KNOB

The CUE VOLUME ROTARY KNOB adjusts your HEADPHONE MONITOR OUTPUT volume.

16 CHANNEL CUE SELECTOR

The CHANNEL CUE SELECTOR allows you to choose which channel will be heard in the headphones, one or all can be pressed at the same time, when pressed a red LED will illuminate indicating the CUE is in the ON position

17 CHANNEL VOLUME FADER

After you have chosen which input you will use with the INPUT SELECTOR the corresponding CHANNEL FADER will allow you to adjust the volume for that particular CHANNEL.

18 CROSSFADER ASSIGNMENT

The fader assignment rotary allows you to assign which two of the 4 channels will be controlled by the CROSSFADER.There are 5 selections for either side of the CROSSFADER which can be either CHANNEL 1,2,3,4 or OFF, In the OFF position the CROSSFADER will not affect the volume of any CHANNEL.

19 CROSSFADER

The CROSSFADER allows you to mix evenly from one source to another. On the MM-4000The CROSSFADER is assignable between either channels (1) and (2) or channels (3) and (4) depending on the position of the fader assignment push button (see above).

The CROSS FADER on the MM-4000is also removable and if the need arises can be replaced.The RG-45(RAILGLIDE™) DUAL-RAIL CROSS FADER, which has internal dual stainless steel rails that allow the slider to ride smoothly and accurately from end to end can be purchased from your local GEMINI dealer.

NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE FADER BACK AND FORTH. PRESSING DOWN ON THE CONTROLS CAN BEND CONTACTS AND CAUSE A

LOSS OF SOUND.

20 CUE/PGM FADER

The CUE/PGM FADER determines the mix between the chosen CHANNEL CUE SELECTION and the MAIN OUTPUT mix.

To the left is the CUE program and to the right is MAIN OUTPUT.

21 POWER SWITCH

Main POWER switch (see above).

22 VU METER

The MM-4000has a VU METER that allows you to monitor the decibel levels of the LEFT and RIGHT MASTER output.

It also has two settings (SEE BELOW)

23 VU METER SETTING SWITCH

The VU SETTING SWITCH allows you to choose between two VU display modes, In the CUE position the VU will display the levels of the headphone CUE, and in the MASTER position the VU will display the MASTER output levels.

2419 MONO/STEREO

The MONO/STEREO switch allows you to change the output of the MM-4000to either MONO output or STEREO output depending on the nature of the system you are playing through, for example some nightclub systems are wired in MONO, this switch gives you the choice to change the output of the MM-4000to either MONO or

STEREO.

EFFECTS:

28 ON/OFF

Turns the effect section ON or OFF.

29 WET/DRY ROTARY

Adjusts the mix between the (DRY) input signal being sent from the effect assigned channels and the processed (WET) signal coming from the effects section.

30 CUE EFX BUTTON

Like the CUE SELECT BUTTONS the CUE EFX BUTTON lets you monitor the effect in the headphone before you mix it in using

DRY/WET ROTARY.

31 EFFECT SELECTION ROTARY

Lets you choose between the 16 different built in effect choices which consist of:

ROOM REVERB:

A short REVERB that mimics the sound of being in a small ROOM this REVERB has three (3) different settings.

PLATE REVERB:

An artificially created REVERB that uses a plate of metal to simulate a highly reflective ROOM sound, this REVERB also has three (3) different settings.

HALL REVERB:

Is a longer REVERB that mimics the sound of being in a concert HALL this also has three (3) different settings.

ECHO:

ECHO is similar to a delay effect which basically repeats the sound and then decays or trails it out mimicing the sound of a canyon or very large area with reflective qualities, this EFFECT also has three

(3) different settings.

VOCAL CANCELLATION:

Can be used to cancel or remove the vocals in a song so you can sing over it.

AUTO WAH:

Is a FILTER that automatically opens and closes giving you the sound similar to that of a WAH WAH pedal used with guitars.

FLANGER:

A FLANGER sounds like two records being played at the exact same time, which give you a tunnel or jet plane type of sound.

AUTO PAN:

AUTO PAN will automaticaly pan the sound from the left speaker to the right speaker at a pre-determined tempo.

5