Azden FMX-42 manual Outputs and Settings Monitor Level and Monitor Output Jack, Monitor Select

OUTPUTS and SETTINGS

Monitor “LEVEL” and “MONITOR” Output Jack:

The “MONITOR” “LEVEL” (22) adjusts the volume of headphones connected to the “MONITOR” output jack (23). Zero is the lowest (quietest) setting, 10 is the highest (loudest).

Monitor “SELECT”:

Normally, the monitor “SELECT” switch (24) is set to position “L/R”. In this position you will monitor the sound of all connected microphones using stereo headphones. If you only want to hear the “L” output, use stereo headphones and set the switch to position “L”. Or, if you only want to hear the “R” output, use stereo headphones and set the switch to position “R”. The use of mono headphones is not recommended.

“OUTPUT” “L” and “R”:

Connect a cable from “OUTPUT” “L” (14) and/or “OUTPUT” “R” (15) to the micro- phone or line input of your video camera or audio recorder. These outputs accept a standard 3-pin female XLR connector equipped cable. Push the cable connector into the output jack until it locks. To remove the connector press the release tab on the connector and pull the connector out.

“OUTPUT” “LEVEL” Settings:

Select the “OUTPUT” “LEVEL” (26) that is best-suited for your video camera or audio recorder. The “+4 dBu” setting is for line-level audio inputs and the “-36 dBu” setting is for a microphone-level audio input.

“STEREO” Mini-Connector Output:

The “STEREO” mini-connector (3.5 mm) output (25) is designed for video cameras or audio recorders which have mini-connector microphone-level inputs.This output is stereo (dual-channel) and unbalanced. It is recommended to use a stereo-to- stereo mini-cable (not supplied) from the “STEREO” mini-connector output to the microphone or line-level input of your video camera or audio recorder. Because the FMX-42 has low-impedance XLR inputs and a mini-connector output, users of mini DV cameras that have mini-connector microphone inputs can now use high- quality microphones with XLR outputs.

“EXTERNAL DC IN”:

For external powering of the mixer, connect a power supply to this input (3). Maximum rating of the power supply should not exceed 12 volts DC, 350mA. Azden recommends using its BC-26U.

“METER ILLUM”:

Turn this switch (27) “ON” to light up the VU Meters and set your audio levels. Turn this switch “OFF” when not using the meters to conserve battery power.

INTRODUCTION:

Thank you for purchasing Azden’s FMX-42 4-channel field mixer. The FMX-42 has many unique features, making it very important to read and understand this manual completely before use. Designed to work with most microphones that have a low- impedance XLR output or line-level devices, the FMX-42’s output can be connected to virtually any video camera or audio recorder, which has XLR or mini-connector mic/line inputs.

POWERING THE FMX-42

Battery Power:

Make sure the mixer is turned “OFF” (2). Remove the battery cover (1) by pressing the clip in and then lifting up and removing the cover from the unit. Install 6 fresh “AA” ALKALINE batteries following the polarity diagram inside the battery compartment. Do not force the batteries. When all 6 batteries are installed, replace the battery cover and move the power switch (2) to the “BATT” position. The “POWER” LED (4) will turn GREEN. When the battery voltage level becomes too low for proper operation the “POWER” LED will turn RED. When this happens replace the batteries with fresh, new “AA” ALKALINE batteries.When not in use, turn the mixer “POWER” switch (2) to “OFF” to conserve battery life.

External Power:

The FMX-42 can be powered from an external power supply. After attaching the power supply to an active 110VAC source and to the “EXT DC IN” jack (3) on the FMX-42, move the power switch (2) to the “EXT” position. The “POWER” LED (4) will turn green. When not in use, turn the mixer “POWER” switch to “OFF” and disconnect the power supply from the mixer.

Note: The FMX-42 is not supplied with an external power supply. An optional power supply,

part number BC-26U, is available from Azden’s web site: www.azdencorp.com.

Wearing the FMX-42:

The FMX-42 is supplied with a ballistic nylon case. Place the mixer in the case and adjust the neck strap to achieve the most comfortable position for you. A back harness (not supplied) can be secured to the metal rings on the case for additional support and comfort.

INPUTS and SETTINGS

“INPUT” Channels: “CH 1”, “CH 2”, “CH 3” and “CH 4”

Connect the output of a microphone, wireless receiver or line-level audio compo- nent to “INPUT CH 1” (5) and/or “CH 2” (5) and/or “CH 3” (5) and/or “CH 4” (5). The inputs accept a standard 3-pin male XLR connector equipped cable. Push the connector into the input jack until it locks. To remove the connector, press the “PUSH” tab (6) and pull the connector out.

4	Illustration numbers:	1
	Shown in the instructions within ( ), these numbers refer to the illustrations on the inside cover.