Beckett Model 7505 manual Priming the Pump, Reset Button Operation, Status Lights

Page 10

Priming the Pump

1.Prepare the burner for priming by attaching a clear plastic hose over the bleed port fitting and fully opening the pump bleed port. Use a suitable container to collect purged oil.

Hot Gas Puff-Back

and Heavy Smoke

Hazard

Failure to bleed the pump properly could result in unstable combustion, hot gas puff- back and heavy smoke.

•Do not allow oil to spray into a hot combustion chamber while bleeding air from the pump.

•Install a gauge in the nozzle discharge port tubing or fully open the pump bleed valve to prevent oil spray from accumulating in the combustion chamber during the air bleed procedure.

•Ensure that all bubbles and froth are purged from the oil supply system before tightening the pump bleed valve.

•Ensure that the appliance is free of oil and oil

Table 2 - Reset Button Operation

2.Initiate a call for heat.

3.After the burner starts, press and hold the reset button for 15 seconds until the yellow light turns on. This indicates that the button has been held long enough.

4.Release the reset button. The yellow light will turn off and the burner will start up again.

5.At burner start up, click the reset button while the igniter is still on. This will transition the control to a dedicated Pump Prime mode, during which the motor, igniter, and valve are powered for four minutes. The yellow light will be on.

6.Bleed the pump until all froth and bubbles are purged. If desired, terminate the call for heat or hold the reset button for at least one second to exit Pump Prime mode and return to Standby.

7.At the end of 4 minutes, the yellow light will turn off and the control will

If the burner is in the

Pushing the reset button will:

 

 

 

below state:

Button Click

Button Hold

Button Hold

 

(press < 1 second)

(press > 1 second)

(press 15+ seconds)

Lockout

Reset from Soft Lockout

Reset from Restricted

(Hard) Lockout

 

 

 

Valve-on Delay, Trial for

Go to Pump Prime (see

Disable the Burner:

Enables Pump Priming:

Ignition, Ignition Carryover

“Priming the Pump” above)

Any time the burner is

After the reset button has

 

 

running, press and hold

been held for 15 seconds,

Run (igniter is shut off)

No action

the reset button to disable

the button can then be

Motor-Off Delay,

No action

the burner. The burner will

clicked during the next

 

remain off as long as the

ignition sequence to enter

Standby

 

 

button is held.

Pump Prime mode.

 

 

Pump Prime

No action

Exit Pump Prime mode and return to Standby

 

 

 

 

Table 3 - Status Lights

Light Color

On Continuously

Flashing

 

 

 

Red

Restricted (Hard) Lockout

Soft Lockout

Green

Flame Sensed during normal operation (Could be stray

Recycle

 

light during standby)

 

Yellow

Control is in Pump Prime mode or

Reset button currently held for 15+ seconds.

N/A

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents GeniSys Description / ApplicationsFeatures Models and Cross Reference GuideGetting to know the control Environmental Ratings Electrical RatingsApprovals Can cause severe injury, death, or property damage WiringMounting Electrical shock can cause severe personal injury or deathTypical Boiler Wiring ValveTypical Furnace Wiring Intermittent ignition, no valve-on or motor-off delaysStartup / Checkout Check Safety FeaturesReset and Service by Qualified Technician only Starting the SystemSequence of Operation Reset Button OperationBurner States Priming the Pump Reset Button OperationStatus Lights Maintenance Disable FunctionLimited Warranty Information

Model 7505 specifications

The Beckett Model 7505 is a highly regarded oil burner that delivers reliable performance, efficiency, and a variety of features that make it a popular choice for both home and commercial heating applications. This burner is designed for use with a range of heating systems, including forced air and hot water boilers, making it a versatile option for many users.

One of the standout features of the Model 7505 is its compact design. Measuring just 18 inches in height, 15 inches in width, and 22 inches in depth, this burner easily fits into tight spaces, allowing for flexible installation options. The burner is equipped with a powerful 0.75 GPH nozzle, which is capable of delivering up to 140,000 BTUs per hour, making it suitable for a variety of heating needs.

The Model 7505 incorporates advanced combustion technology, designed to optimize fuel efficiency and minimize emissions. The burner features a high-efficiency combustion head that helps to ensure a complete burn of the oil, leading to lower fuel consumption and reduced greenhouse gas emissions. This commitment to efficiency not only helps the environment but also translates to savings on fuel costs for users.

Moreover, the Beckett Model 7505 comes with a unique primary control unit that enhances the burner's safety and performance. This control unit features an integral reset button, an adjustable primary air setting, and an LED indicator light that provides at-a-glance status updates on operations. These smart features simplify troubleshooting and ensure safe operation of the heating system.

In addition to its impressive performance capabilities, the Model 7505 is designed for durability. Constructed with high-quality materials, including a robust steel casing and a corrosion-resistant finish, this oil burner can withstand the rigors of regular use in various environments.

Maintenance is also made easy, thanks to the removable panels and access points that allow for quick and efficient servicing. Beckett's reputation for reliability and longevity makes the Model 7505 a wise investment for those seeking a dependable heating solution.

Overall, the Beckett Model 7505 stands out with its combination of efficiency, safety, and ease of use. Whether for heating residential properties or commercial spaces, the Model 7505 continues to be a go-to choice for many satisfied customers.
Top Page Image Contents