Berkel X13A important safety instructions General, Automatic Operation

Page 9

Operation

General

1.Check to see that the center plate and product table are in place on the slicer and the gauge plate is completely closed. The holes in the bottom of the center plate fit over the bottom mounting studs in the ring guard and the center plate locking knob at the top of the center plate fits over the top edge of the ring guard. The product table slides completely onto the support arm and is secured with the red product table locking knob. The table can only be removed if the thickness control knob is closed and the product table is pulled to the front of the slicer.

2.If the slicer is an automatic, then make sure the automatic engage knob on the right side of the table support arm is pushed in, towards the left.

3.Plug the slicer in. The pilot light, between the start and stop buttons will illuminate.

4.Push the green ON button and the slicer blade will start to turn. Press the red STOP button to stop the knife.

Automatic Operation

5.If you have an automatic slicer, with the slicer stopped, pull the automatic engage knob fully out on the right side of the machine. This will put the slicer in the automatic mode.

6.Push the speed selection button to change the speed:

One illuminated LED indicates 20 slices per minute (slow speed)

Two illuminated LED’s indicates 40 slices per minute (medium speed)

Three illuminated LED’s indicates 60 slices per minute (high speed)

7.Pushing the stroke length selection button changes the length of the stroke. This allows smaller products to be sliced quicker, without the table moving any faster. Make sure the stroke length is longer than the width of the product.

One illuminated LED indicates 1/3 of the total possible stroke length

Two illuminated LED’s indicates 2/3 total possible stroke length

Three illuminated LED’s indicates full stroke length

8.Press the green START button and the product table will slowly come to its forward position to find its home position. Once it gets back to the home position, then it will start to go back and forth at the preset speed and stroke length.

9.Push the red STOP button and the table will complete its stroke and stop in the home position.

10.As long as the slicer remains in the automatic mode it will remember its home position and always start right up when the green START button is pushed. It will always start slow and gradually build up to its full speed. This is the “soft start” feature.

11.Each time you take the slicer out of the automatic mode, and then back into the automatic mode, it will always find its home position before it starts to run (as indicated in step #8).

12.Each time you active the slicer into automatic mode, the last speed and stroke length settings will be remembered until power is disrupted from the slicer (i.e. disconnecting the power cord from the outlet). Once power is reconnected to the slicer, the default for automatic is slow speed and full stroke length.

X13 & X13A OWNER/OPERATOR MANUAL • 7

Image 9
Contents MODELS X13 & X13ASLICERS OWNER/OPERATOR MANUALINGS RELATED TO YOUR PERSONAL SAFETYARE INDICATED BY Remember, however, THIS MANUAL OR THE WARNING LABELS DOBEFORE USING THIS EQUIPMENT Page TABLE OF CONTENTS800348-0251 Form No. OMGX-0206NPELIGRO CUCHILLAFILOSApara evitar serios accidentes a su persona siga las instrucciones de este manual ySHARP KNIFE BLADE to avoid serious personal injuryfollow all the instructions in this manual and Switch and speed/stroke selection on X13A Thickness Control Knob EQUIPMENT DESCRIPTIONPusher Slide Bar Pusher Handle ON/OFF Product Table HandleCenter Plate Locking Knob Pusher Gauge Plate SupportArm Product Table Center Plate Product Table Locking Knob Center Plate Mounting StudAutomatic Engage Knob X13A only Unpacking and Installation Intended Uses and CharacteristicsSpecial Features/Characteristics Intended UsesOperation GeneralAutomatic Operation Procedure CAUTION Use extreme care when cleaning blade Cleaning and SanitizingLoading product Supplies6. Pre-scrape food from removable product table and center plate Repair Parts/Repair Service/Exploded Views Sharpeningbeen cleaned. You cannot effectively sharpen a dirty knife Electrical Failure TroubleshootingCan’t remove product table Product table doesn’t move freelySpecifications Optional Accessories SLAW TRAYJUICE CUP 1 Model 180 slicers carry a 90-day warranty Warranty