American Panel AP20BC175-2 user manual The P.C. baud rate should be left at

Page 17

The P.C. baud rate should be left at 38400.

AP20BC175-2 Manual

p. To change to YES or NO, press or then

press .

INITIAL PROGRAMMING

SHOCK FREEZE?

NO

NO Blinks

q. To change to YES or NO, press or then

press .

INITIAL PROGRAMMING

UV CYCLE?

NO

NO Blinks

r.To change to YES or NO, press or then

press .

INITIAL PROGRAMMING

DEFROST CYCLE?

YES

YES Blinks

INITIAL PROGRAMMING

s. To change to YES or NO, press		or	then	PC CONNECTION?
				PC CONNECTION?				NO Blinks
					NO			NO Blinks
press	.
For YES, the display will show:
The P.C. baud rate should be left at 38400.				INITIAL PROGRAMMING
However, to make a change:
However, to make a change:				PC BAUDRATE			38400		Blinks
							38400

t. To change the baud rate, press		or	then		38400
t. To change the baud rate, press		or	then
press	.
u. To change the number (between 01 & 32), press
u. To change the number (between 01 & 32), press				INITIAL PROGRAMMING
or	then press	.		CHILLER NETWORK ID				01 Blinks
or	then press	.			# 01			01 Blinks


				INITIAL PROGRAMMING
v. To change to YES or NO, press		or	then	PRINTER CONNECTION?
					YES			YES	Blinks
press	.				YES				Blinks
press	.
For YES, the display will show:
The printer baud rate should be left at 1200.				INITIAL PROGRAMMING
However, to make a change:				PRINTER BAUDRATE
				PRINTER BAUDRATE
					1200			1200	Blinks
w.To change the baud rate, press		or	then		1200				Blinks
w.To change the baud rate, press		or	then
press	.

				INITIAL PROGRAMMING
x. To change the timing, press		or	then	PRINT & SAVE EVENTS
				PRINT & SAVE EVENTS				15 Blinks
				EVERY	15 MIN			15 Blinks
				EVERY	15 MIN
press	.

16

Image 17

Contents REV. C American Panel CorporationE-mail service@americanpanel.com USER’S MANUALINSTALLATION INSTALLATION OF REMOTE UNITSUSING THE HURRICHILL TECHNOLOGY INDEXWIRING DIAGRAMS MAINTENANCE AND CLEANINGPARTS LIST STANDARD WARRANTYOPERATING MODES CONTROLLER FEATURESINTRODUCTION ADDITIONAL CYCLES OPERATING CYCLESPRINTER PC CONNECTION OPTIONALINSTALLATION AT THE SAME LEVEL INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS CONNECTION PIPING FOR REMOTE CONDENSING UNITS INSTALLATION AT DIFFERENT LEVELSINSTALLATION INSTALLATIONDIMENSIONS ELECTRICAL AND REFRIGERATION SPECIFICATIONSCONDENSATE DRAINAGE CONNECTION VERIFYING CORRECT INSTALLATIONCONNECTION TO THE REMOTE UNIT SPACES AROUND THE CABINET STARTING & TESTING THE UNITBLAST CHILLING USING THE HURRICHILL TECHNOLOGYSHOCK FREEZING SOFT CHILL CYCLELOADING PANNING AND LOADINGPANNING CONTROL PANEL FOR MODEL AP20BC175-2 BLAST CHILLER KEY COMBINATIONS KEYBOARD KEYSON/OFF & START/STOP PROGRAMMING KEYS1. INITIAL PROGRAMMING PROGRAMMINGThe low air alarm temperature should be left at The high air alarm temperature should be left atThe high food alarm temperature should be left at The low food alarm temperature should be left atThe printer baud rate should be left at The P.C. baud rate should be left atAUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING 2. PROGRAMMING THE CYCLESAUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING p. To change the temperature, press DEFROST CYCLE PARAMETERS PROGRAMMINGthen press q. To change the temperature, pressMANUAL SOFT CYCLE PARAMETERS PROGRAMMING MANUAL HARD CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING 1. AUTOMATIC MODE - SOFT CHILL OPERATIONalternating 2. MANUAL MODE - SOFT CHILL4. DEFROST CYCLE 3. HARD CHILL CYCLEb. Open the door 6. TO CLEAR DATA 5. PREPARING AND USING THE PRINTERPRINTER LOADING A ROLL OF PAPER MAINTENANCEREMOVING A ROLL OF PAPER OPERATING THE PRINTERREPLACING THE RIBBON WITH PAPER IN THE PRINTER MAINTENANCE AND CLEANINGCLEANING THE STORAGE COMPARTMENT WIRING DIAGRAMSCLEANING THE CONDENSER AP20BC175-2 Manual AP20BC175-2 Manual AP20BC175-2 Manual COMPUTER CONNECTION DESCRIPTION PARTS LISTPART # installing contractor. It is not covered by this Warranty STANDARD WARRANTYAMERICAN PANEL CORP 5800 S.E. 78th Street, Ocala, FloridaORDERING PRINTER SUPPLIES RIBBON & PAPER