Moyer Diebel MH-6LM2, MH-6NM2, MH-60M2 technical manual Chemical Connections

Page 17

INSTALLATION

Chemical Connections (Cont.)

Refer to Fig. 12

5.A 1/2" NPT detergent probe injection point is provided at the rear of the dishwasher.

6.Detergent may be added manually if your dishwasher is not equipped with dispensing equipment. Consult your chemical supplier for recommended amounts.

Refer to Fig. 13

7.A 1/8" NPT rinse aid injection point is provided in the final rinse manifold. Use a liquid rinse aid.

The manifold is located on the top right side of the dishwasher.

8.MH-6L Only

A 1/4" NPT sanitizer injection point is provided in the final rinse manifold.

Models MH-60 and MH-6N do not require sanitizer.

9.Use a sodium hypochlorite (Chlorine) based sanitizer at a minimum concentration of 50PPM in the final rinse.

10.Use chlorine test papers to verify and monitor the 50PPM chlorine level.

WARNING:

!Never premix rinse aid with the sanitizing agent. Mixing may cause hazardous gases to form.

CAUTION:

! Some metal, includng silver, aluminum and pewter are attacked by sodium hypochlorinte (chlorine). Avoid cleaning these metals in a MH-6L.

Figure 12

Detergent Probe Injection Point

1/2" NPT

(Wash Tank Rear)

1/4" NPT Sanitizer

Injection Point

Model MH-6L Only

1/8" NPT Rinse aid Injection Point Models MH-60, MH-6N, MH-6L

Figure 13

Rinse Aid and

Sanitizer Injection Points

(Top of Dishwasher)

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents MH-6LM2 MH-6NM2Moyer Diebel, US Revision History Contents List of Figures Limited Warranty Welcome to Moyer Diebel IntroductionOptions MH-60 only AccessoriesStandard Equipment includes Electrical Power Requirements Unpack the dishwasher InstallationPlacement for Corner Operation Electrical Connections InstallationHinged Control Panel Water Connections Plumbing ConnectionsVentilation Drain ConnectionsChemical Connections Chemical Dispenser Signal Terminal BlockChemical Connections Initial START-UP Complete the installationInstall the Scrap Screens Drain-Overflow Assembly Initial START-UP Check Wash Water TemperatureInitial START-UP Check Final Rinse Water Pressure Check Final Rinse Water TemperatureDrain the dishwasher Extended Wash OperationComplete the initial start-up Initial START-UP Action Result Operation SummaryCleaning Schedule CleaningDeliming Condition Cause Solution TroubleshootingTroubleshooting Troubleshooting Basic ServiceMotor Overloads Electrical ServiceFill Timer Electrical Service TimersCycle Timer Configuration a Electrical Service Motor Connections Pump Seal Replacement Mechanical ServiceReplacement Parts Door Assemblies and Panels Part Part Description Qty Item No Door Assemblies and PanelsDoor Safety Switch and Instrument Panel Door Safety Switch Instrument Panel 1112 Door Handle Assembly and Springs Track Assembly Corner configuration shown Track Assembly Model MH-60 Fill Piping Assembly MH-6L MH-6N, MH-6L Wash/Rinse Spray Arm Assembly WASH/RINSE Spray ARM Assembly MH-60, MH-6N, MH-6L Wash/Rinse Spray Piping Assembly WASH/RINSE Spray Piping Assembly Scrap Screens and Drain Assembly Scrap Screens and Drain Assembly Pump Assembly Pump Assembly Wash Tank Heater and Thermostats 0509185 Wash Tank Heater and ThermostatsMH-60 Only Electric Booster Assembly MH-60 only Electric Booster Assembly 1419 1520 Control Cabinet Dishracks 101285 DishracksElectrical Schematics Diagram State End of Cycle Power- Off Door- Closed Timer Chart

MH-6LM2, MH-60M2, MH-6NM2 specifications

Moyer Diebel has made a significant impact in the commercial dishwashing sector with its innovative models such as the MH-6NM2, MH-60M2, and MH-6LM2. These commercial dishwashers cater to a range of operational needs, ensuring high efficiency, reliability, and ease of use, vital for any busy kitchen environment.

The MH-6NM2 model serves as an exemplary choice for establishments requiring a high-capacity solution. This dishwasher boasts a unique design that allows for rapid wash cycles, ensuring dishes and utensils are cleaned within minutes. With a large wash chamber, the MH-6NM2 is capable of accommodating a variety of dish types, including plates, pots, and pans. Its high-temperature wash feature not only guarantees sanitation but also enhances drying efficiency. Additionally, the model is equipped with an advanced rinse system that minimizes water usage while maximizing cleaning results, making it an eco-friendly choice for modern kitchens.

Moving to the MH-60M2, this model stands out with its impressive versatility. Designed for medium to large operations, it features robust construction and an array of programmable cycle options. The MH-60M2 includes user-friendly controls and a digital display that simplifies operation and monitoring. Its innovative filtration system significantly reduces maintenance needs by ensuring that food particles do not hinder performance. The machine is also designed to operate quietly, which is an essential feature in busy dining environments where noise control is paramount.

The MH-6LM2 is engineered to meet the demands of high-volume usage in delicate environments, such as fine dining restaurants. This model combines efficiency with advanced cleaning technology, allowing for gentle handling of glassware while providing exceptional cleaning results. The MH-6LM2's energy-efficient design not only cuts down on utility bills but also supports sustainability efforts by reducing water consumption. Its built-in self-diagnostics capabilities allow for easy troubleshooting and maintenance, reducing downtime and ensuring that the kitchen runs smoothly.

In summary, Moyer Diebel's MH-6NM2, MH-60M2, and MH-6LM2 models reflect the company’s commitment to excellence in commercial dishwashing. With advanced technologies, user-friendly features, and a focus on efficiency and sustainability, these machines are well-suited for various commercial applications, providing reliable performance that meets the high demands of any kitchen.
Top Page Image Contents