TROUBLESHOOTING GUIDE
SYMPTOM | CAUSE | POSSIBLE SOLUTION |
|
|
|
Burner will not light | Not enough gas flow from propane | Open propane tank all the way |
| tank |
|
BURNER LIGHTING INSTRUCTIONS
1.Check the regulator to be certain it is in the OFF position before connecting to the gas cylinder. Perform soapy water test before each use.
2.Open tank cylinder valve.
LOW BATTERY GAS FLOW
3. To start timer operation, push POWER button; both lights will blink once. | Flujo el gas |
Basse Batterie | |
Batteria Baja | Ecoulement de gaz |
| Low gas level in propane tank, or | Check gas level in propane tank | |
| tank is empty |
| |
|
|
| |
| Blockage in burner | Clean and check burner for spiders, | |
|
| insect nests, or other debris | |
|
|
| |
| Faulty burner | Contact Masterbuilt at | |
|
| 1.800.489.1581 | |
|
|
| |
Hissing or gurgling sounds coming | Water in burner | Check burner for moisture, make | |
through gas train from tank to |
| sure burner is dry | |
burner |
|
| |
Damaged hose | Perform soapy water test to check | ||
| |||
|
| for cracks - See page 14 |
4.Press START button; green light will remain on, allowing 15 minutes of gas flow.
5.Turn regulator on.
6.Place a lit match to the burner from under the wind shield as shown below.
7.Slowly turn regulator control knob clockwise until the burner lights.
•Timer will run 15 minutes before shutting gas flow off.
START
COMIENZO
POWER
ENERGIA
PUISSANCE
| Gas leak | Check all connections in gas train for |
|
| possible leaks - See page 14 |
|
|
|
Timer does not work | Batteries are dead | Replace batteries - See page 11 |
|
|
|
| Did not press power or start button | Follow timer instructions - See page |
|
| 10 |
|
|
|
| Faulty timer | Contact Masterbuilt at |
|
| 1.800.489.1581 |
|
|
|
Timer stopped before time was up | Batteries are dead | Replace batteries - See page 11 |
|
|
|
Excessively yellow and irregular | Blockage in burner | Clean and check burner for spiders, |
flame |
| insect nests, and other debris. |
|
|
|
| Air damper not adjusted correctly | Adjust air shutter to the burner until |
|
| the burner flame is as blue as |
|
| possible - See page 9 |
|
|
|
Flame has gone out | Low gas level in propane tank, or | Check gas level in propane tank |
| tank is empty |
|
|
|
|
| Too much wind | Check wind direction and set cooker |
|
| away from windy areas - See page 3 |
|
|
|
| Blockage in burner | Clean and check burner for spiders, |
|
| insect nests, and other debris |
|
|
|
| Water in burner | Check burner for moisture, make |
|
| sure burner is dry |
|
|
|
| Faulty burner | Contact Masterbuilt at |
|
| 1.800.489.1581 |
•At 5 minutes remaining, gas flow light will blink slowly. At 2 minutes remaining gas flow light will blink quickly.
•If burner does not light within 5 seconds, turn regulator control valve OFF, then turn gas cylinder valve OFF. Wait 5 minutes for fumes to diminish, turn timer knob clockwise until its stops before relighting.
•If the flame is blown out wait 5 minutes for fumes to diminish before resetting timer and relighting.
•After the burner is lit, open the regulator valve until the flame increases. Use the air shutter on the burner to adjust the flame until it turns blue. Reduce flame.
•Fill Pot with water or oil. DO NOT fill pot more than 1/3 the pots full capacity. This will help avoid dangerous
•Bring water or oil to the desired temperature by adjusting regulator control valve. Oil should never exceed 400°F (204°C). Oil will ignite at 550°F (287°C) to 700°F (371°C).
•Always use a thermometer when frying.
•After each use, first turn the regulator control valve OFF, then turn the gas cylinder OFF. Always allow fryer stand and pot with water or oil to cool completely before touching, moving, or storing.
FLAME VIEWING HOLE
LIGHTING POSITION
13 | 10 |