Broilmaster SBG2801-1 manual Propane GAS Grills, See Figure Pressure Regulator and Hose Assembly

Page 14

PROPANE GAS GRILLS (cont.)

Installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1. In Canada, installation shall be in accordance with CAN/CGA-B149.2 Propane Installation Code, or CAN/CGA-B149.1 Natural Gas Installation Code, and local codes where applicable. Consult your local gas supplier or propane gas dealer for code regulations and recom- mended procedures.

Warning: Superb by Broilmaster® Gas Grills require Liquid Propane (LP) cylinders equipped with an Overfill Protection Device (OPD). An overfilled or improperly filled Propane cyl- inder can be dangerous.

Always use the pressure regulator and hose assembly supplied with your Propane gas grill.

Note: Not all valve and cylinder combinations are compatible. Check warning tag on valve and cylinder as well as external fit- ting threads.

All Broilmaster pressure regulators and hose assemblies require Propane cylinders with a Type 1 connection device as illustrated.

See Figure 16.

Pressure Regulator and Hose Assembly

The pressure regulator has an outlet pressure of not more than eleven (11”) inches water column. It must be connected to the Propane gas cylinder’s female valve outlet before the grill can be operated.

Caution: Operation of a propane gas grill without the pres- sure regulator and hose assembly will cause gas leaks which could lead to fire or explosion, resulting in property damage or personal injury.

The pressure regulator’s fitting must remain clean and free of nicks and scratches. A dirty, nicked or scratched fitting can cause a gas leak, resulting in an explosion or fire. Use only genuine Broilmaster® replacement parts unless otherwise specified by the manufacturer.

Connecting to Propane Gas / Cylinder Retention Means

Attention: Propane gas cylinders that are acceptable for use with this grill must comply with “Cylinder Requirements” section and “Connection Requirements” section (Pages 13-14.)

Lift up the tank ring. Position the cylinder in the opening at the bottom of the cart then fit the tank ring out side of the tank. See

Figure 15.

Figure 15

Attach the pressure regulator to the Propane gas cylinder’s valve using the plastic handwheel. Tighten in a clockwise motion to achieve a gas tight seal. See Figure 16.

Clockwise

Figure 16

Caution: Do not use a wrench or any other tool to tighten. Use of a wrench or other tool will damage the plastic handwheel.

Fit hose to the hook inside of the right side panel. See Figure 17.

Figure 17

To disconnect the Propane gas cylinder, turn OFF the cylinder’s valve and the grill’s control valve. Remove the regulator by turning the plastic handwheel counterclockwise.

Page 14

SBB00101-1-1007

Image 14
Contents SBG2500-1, SBG2501-1 and SBG2801-1 Gas Grill If YOU Smell GAS Congratulations Empire Comfort Systems, IncTable of Contents Hardware Package Parts View SBG2801 Description Parts ListIndex No Part Number SBG2500 Grill Mountings Grill AssemblyBefore You Begin Gas Consumption on Grill BurnersCart and Grill Assembly See FigureCart and Grill Assembly Rotisserie Installation for SBG2501-1 & SBG2801-1 Using the Ignitor Rotisserie CounterbalancePropane GAS Grills Propane GAS Grills See Figure Pressure Regulator and Hose AssemblyConnecting to Propane Gas / Cylinder Retention Means GAS Conversion to Natural GAS Operating Instructions Using Matches Air Shutter AdjustmentOperating Instructions Using the Ignitor OperationBefore Cooking Electrical AccessoriesOperation PreheatingMaintenance Troubleshooting Problem Cause SolutionYear Against Rust-Through Warranty TermsYears Against Rust-Through Service Notes Service Notes Service Notes Broilmaster