Safety Shielding, Safety Lighting | Kuhn Rikon 5000 Series specs

5000TROPR 005893 R022504

MIXER SETUP

IMPORTANT! READ BEFORE OPERATING MIXER.

IT IS THE RESPONSIBILITY OF THE OWNER TO MAKE SURE THE MIXER IS SET

UP PROPERLY. THE FOLLOWING RECOMMENDATIONS SHOULD BE HELPFUL

SAFETY SHIELDING

Be sure all shielding is in place and functioning properly. Replace all damaged or missing shielding immediately - see parts pages or call your dealer for replacement safety shielding part numbers.

SAFETY LIGHTING

The lighting system provided is intended for agricultural tractor transport only. If the mixer will be transported on a public roadway, be sure the lights are in good working order. When attaching to a towing vehicle other than a tractor, always check for proper operation, as wiring may vary.

LUBRICATION

Check to be sure that all gearcases and oil bath contain oil, and that bearings and joints have been greased (see maintenance section)

CLEVIS SETUP

The clevis (and the clevis mount) on the front of the mixer can be adjusted for height. Mount the clevis so that the mixer is as level as possible when connected to the tractor. Be sure that the PTO driveline does not contact the clevis (or clevis mount) during normal operation or transport.

The clevis is adjustable vertically on all models and can be rotated 360°

to allow for maximum adjustment only on 5032/5042/5055/5073.	THE CLEVIS COULD DAMAGE PTO DRIVELINE IF
Care should be taken in rotating for low tongue	OPERATED ON UNEVEN TERRAIN WITH CLEVIS
height due to potential PTO shaft interference.	ADJUSTED AS SHOWN.
height due to potential PTO shaft interference.	THIS SETTING IS NOT RECOMMENDED
A hitch pin with a minimum of 1 1/4” diameter
with a retainer pin is recommended.

SCALE SETUP

Connect the power cord to the mixer battery or 12V tractor connection and check the scale for proper operation (see scale manual).

POWER CHUTE (option) ADJUSTMENT

To adjust the height of the power chute, change the length of the link chains on the sides of the chute. For best performance, the unloading height should be set at the lowest height possible . The discharge tip-off on the power chute should be adjusted for correct magnet and discharge angle. Loosen the adjusting bolts and tighten at desired tip-off angle.

MIXER RUN-IN

1.Check for proper assembly, adjustment, and lubrication. Check to see that there is adequate oil in the gearboxes and bull gear oil bath. If unit is equipped with a discharge chute, oil the roller chains and check to be sure all bolts and set screws are tight. Review Operating Safety Precautions and Lubrication Instructions before operating the mixer.

2.Be sure all shields are properly in place.

3.Check for and remove any foreign objects in the mixer hopper and discharge opening.

4.Check to see that the door is closed.

5.Be sure no one is inside the mixer.

6.Test run the mixer. a. Make sure mixer is empty, then start the mixer.

b.Run mixer for at least five minutes at 3/4 of rated PTO RPM.

c.If unit is equipped with power chute, run discharge for 1 hour with no load for proper motor break in.

d.Raise and lower the door and the chute or slide tray several times.

e.Disengage the mixer, turn off the tractor engine, and remove driveline.

f.Check the mixer drive components to be sure they are not abnormally hot.

If any of these items are not running as indicated, immediately repair or contact your local dealer. Always refer to Operating Safety Precautions before operating or servicing the mixer.

KUHN KNIGHT, INC.	13
1501 West 7th Ave., Brodhead, WI 53520

701 Cherry Ave., Greeley, CO 80632

5000 Series, Verti-Maxx Mixer specifications

The Kuhn Rikon Verti-Maxx Mixer, 5000 Series, represents a significant advancement in kitchen technology designed for both home chefs and culinary professionals. This innovative mixer combines functionality with precision, ensuring a seamless mixing experience for a variety of recipes.

One of the standout features of the Verti-Maxx Mixer is its unique vertical design. Unlike traditional mixers, this model utilizes a vertical mixing bowl that allows for more efficient mixing and aeration of ingredients. This design not only saves counter space but also ensures that even dense mixtures achieve optimal consistency without the need for excessive manual intervention.

The mixer is equipped with a robust, high-performance motor that delivers reliable power for a range of mixing tasks. Whether you are whipping cream, kneading dough, or mixing cake batter, the Verti-Maxx provides consistent results every time. With multiple speed settings, users can customize the mixing intensity to suit their needs, ensuring perfect results whether working with light or heavy ingredients.

In terms of technology, the Kuhn Rikon Verti-Maxx incorporates a patented mixing mechanism that minimizes air pockets and enhances the overall mixing process. This innovative system allows for a thorough blend of ingredients, reducing mixing time and increasing efficiency in the kitchen. The inclusion of an easy-to-read digital display provides users with real-time feedback on mixing speed and time, enhancing the overall user experience.

Another notable characteristic of the 5000 Series is its easy-to-clean features. The mixer comes with a detachable bowl and mixing attachments that are dishwasher-safe, making cleanup a breeze. The mixer’s sleek, modern design also means that it looks great on any kitchen countertop, merging style with functionality.

Safety is paramount with the Kuhn Rikon Verti-Maxx Mixer. It includes a safety lock mechanism that prevents the motor from running unless the bowl and lid are securely in place. This thoughtful feature ensures peace of mind while mixing even the heaviest of ingredients.

Overall, the Kuhn Rikon Verti-Maxx Mixer, 5000 Series, embodies state-of-the-art kitchen technology, combining practical features with elegant design. Its unique vertical mixing approach, powerful motor, and user-friendly interfaces make it an essential tool for any cooking enthusiast looking to elevate their culinary creations.