Kuhn Rikon 5100 Mixer Setup, Safety Shields, Lubrication, PTO Driveline Setup and Adjustment

Page 13

5100TK OPR 6270US R060106

MIXER SETUP

READ AND FOLLOW THESE INSTRUCTIONS WHEN SETTING UP THE MACHINE.

To avoid personal injury: The hopper floor may be slippery and the augers can spin unexpectedly when stepped on. Use caution when stepping or standing inside the unit and put a protective cover over the auger knives.

SAFETY SHIELDS

Be sure all safety shields are in place and functioning properly. Replace all damaged or missing shields immediately. See parts manual for replacement safety shield part numbers.

LUBRICATION

Check to be sure that all gear cases and oil bath enclosures contain oil, and that bearings and joints have been greased. (See maintenance section)

PTO DRIVELINE SETUP AND ADJUSTMENT

FOR MODEL 5144

The driveline connecting the two 2:1 gearboxes has a shearbolt protection device to protect the machine in an overload situation. If the driveline spins freely, the shear bolt has broken and needs to be replaced. Replace the broken shear bolt with a new 1/4” x 2” grade 5 bolt. Always replace the shear bolt with the same size and grade as the original for proper operation.

FOR MODELS 5173, 5185 AND 51100

The final driveline before the planetary gearbox has a torque disconnect device to protect the machine in an overload situation. The torque disconnect type of driveline protection is an automatic, no maintenance form of protection when compared to shear bolt or friction type clutches. It uses pawls spring loaded into a ratchet to transmit torque.

When the torque overcomes the spring force the pawls pull away from the rachet preventing driveline damage. To reset, simply throttle the truck down and the pawls will reengage. If an obstruction must be removed to get it to reengage, always shut the truck off and remove the key from the truck’s ignition before removing the obstruc- tion.

NOTE: Torque the lock bolt of the truck driveline to 75ft. lbs. (17mm 6pt socket suggested).

TEST RUNNING THE MIXER

1.Check for proper assembly, adjustment, and lubrication. Check to see that there is adequate oil in the gear- boxes and/or bull gear oil bath. If unit is equipped with a discharge chute, oil the roller chains and check to be sure all bolts and set screws are tight. Review Operating Safety Precautions and Lubrication Instructions be- fore operating the mixer.

2.Be sure all shields are properly in place.

3.Check for and remove any foreign objects in the mixer hopper and discharge opening.

4.Check to see that the door is closed.

5.Be sure no one is inside the mixer.

6.Test run the mixer. a. Make sure mixer is empty, then start the mixer.

b.Run mixer for at least five minutes at 3/4 of rated PTO RPM.

c.Raise and lower the door and the chute or slide tray several times.

d.Disengage the mixer, turn off the truck engine, and remove the key from the ignition.

e.Check the mixer drive components to be sure they are not abnormally hot.

If any of these items are not running as indicated, immediately repair or contact your local dealer. Always refer to Operating Safety Precautions before operating or servicing the mixer.

13

Back to Table of Contents

Image 13
Contents Vertical Maxx Mixer Table of Contents Lubrication for 5144, 5156 Lubrication for 5173, 5185 Introduction Using this ManualModel and Serial Number Information Understand Safety Words and Symbols SafetyFollow Safety Instructions and Precautions Read the OPERATOR’S ManualOperating Safety Precautions Transporting Safety Precautions Unit Safety DecalsSafety RED Reflector Models 5144, 5156, 5168, 5173, 5185 Safety Decal PlacementSafety Safety Shields Mixer SetupPTO Driveline Setup and Adjustment LubricationMixer Operation SafetyGeneral LimitationsMixer Setup Operation Using Mechanical DriveAdjustments Step #1 Processing MaterialsLoading Sequence Step #2 Mixing MaterialsStep #3 Unloading Step #4 Other Mixing Recommendations Operation Using Hydrostatic DriveStep #1 Processing Materials Step #2 Mixing Materials Step #3 Unloading Removing Knives Knife AdjustmentAdding Knives Moving Knives in or OUTHAY Stop Adjustment Mixer Operation Optional Equipment Inspection & Adjustments Inspection and AdjustmentsLubrication for 5144, 5156 MaintenanceLubrication for 5173, 5185 Planetary Gearbox OIL Change MaintenanceMiscellaneous Specifications 5144, 5156 Specifications 5173, 5185