Keurig B60 manual Set-Up & First Brew, Ready to Brew Your First Cup

SECTION 1 Set-Up & First Brew

IMPORTANT: You cannot use your Keurig® Brewer until it has been set-up for its first use as set forth below.

NOTE: If Brewer has been exposed to temperatures below freezing, allow Brewer at least two hours to reach room temperature before brewing. A frozen or extremely cold Brewer will not operate.

fig. 1 Setting Up Your Brewer

1.Unwrap cord and plug the Brewer into

a grounded outlet. Remove all pieces of packing tape and clear plastic sticker from LCD Control Center.

Lock Tabs

Power

fig. 2

fig. 3

4.	Fill Water Reservoir with bottled or filtered
	water so that the water level is just below the
	top edge of the Water Reservoir.
5.	Place Water Reservoir base into the left side
	of the Brewer and be sure the Water Reservoir
	Lock Tabs engage with the Brewer. Replace
	Lid on Water Reservoir.
6.	Press the Power Button found directly
	above the LCD Control Center (fig. 3).
7.	The LCD Control Center will illuminate and
	indicate “NOT READY.” NOTE: A K-Cup®pack
	should not be used for this sequence.
	NOTE: If the Water Reservoir is empty or
	not in place on the Brewer, the LCD Control

fig. 4

NOT READY

fig. 5

8.The Brewer will automatically fill the internal tank with water and then the water will be heated. This will take about 4 minutes. During the heating period, “NOT READY” (fig. 4) is indicated on the LCD Control Center. Do not lift Handle during this heating period.

Once the water is heated, “READY TO BREW” will be indicated and the Brew Buttons will be illuminated (fig. 5). NOTE: You may see small amounts of water coming from the Vent and dripping into the Water Reservoir during this and subsequent heating — this is normal.

9.Lift and lower the Handle. Press the Small Mug Button to start a cleansing brew. Pour the hot water into the sink.

fig. 6

fig. 7

Ready to Brew Your First Cup

1.LCD Control Center will indicate “READY TO BREW.”

2.Place a cup or mug on the Drip Tray Plate.

3.Lift the Handle and the K-Cup®Pack Holder will open toward you (fig. 6).

4. Select a K-Cup®pack.

NOTE: Do not remove the foil lid or puncture the K-Cup®pack.

5. Place a K-Cup®pack in the

K-Cup®Pack Holder (fig. 7).

CAUTION: There are two sharp needles that

puncture the K-Cup®pack, one above the

K-Cup®Pack Holder and the other in the bottom

of the K-Cup®Pack Holder. To avoid risk of

2. Place a large mug (10 oz. minimum) on the Drip Tray Plate.

3. Remove the Water Reservoir from Brewer by first removing Lid from Reservoir (fig. 1), then lifting Reservoir straight up and away from Brewer (may be tight), (fig. 2). Rinse with fresh water.

NOT READY

ADD

WATER

Center will also indicate “ADD WATER.” None

of the buttons will be activated until water

is added to the Water Reservoir and Water

Reservoir is in place.

READY

TO BREW

MENU

Small

Mug

10.The one-timeset-up process is now complete and you are ready to brew! NOTE: The Brewer may take 15 seconds between brews and then “READY TO BREW” will be indicated.

injury, do not put your fingers in the K-Cup®

Pack Assembly Housing.

6. Lower the Handle to close the Lid over the

K-Cup®Pack Holder. (When it is closed

completely, the LCD Control Center will

indicate “READY TO BREW” and the Small

Cup, Small Mug and Large Mug Buttons will

flash for up to 60 seconds.)

6

7