Keurig B60 manual Cleaning & Maintenance, Programming Brew Temperature 187 - 192º F

SECTION 2 Controls & Indicators (LCD Control Center)

Programming Brew Temperature (187° – 192º F)

The Brewer brews at a preset temperature of 192°. You can adjust this temperature down by 5 degrees if you prefer a cooler cup of coffee, tea or hot cocoa. Simply follow the instructions below.

1.	Press the Menu Button on the LCD Control Center five times to
	program the Brew Temperature feature.
2.	The LCD Control Center will now display the programming options with
	a small arrow next to “SET BREW TEMP” (fig. 15). Also, the temperature
	192° (initial setting) will be indicated at the bottom of the LCD Control
	Center to indicate the current temperature setting.
3.	A minus sign will appear over the Small Cup Button and/or a plus sign
	over the Large Mug Button. Use these buttons to raise or lower the

SECTION 3 Cleaning & Maintenance

Cleaning External Parts

Regular cleaning of the Brewer’s external components is recommended.

1.Never immerse the Brewer in water or other liquids. The Housing and other external components may be cleaned with a soapy, damp, non-abrasive cloth.

2.The Drip Tray can accumulate up to 8 oz. of overflow. The Drip Tray and Drip Tray Plate should be periodically inspected and rinsed clean. To remove the Drip Tray Assembly, simply slide it toward you, keeping it level at all times to avoid spilling. The Drip Tray and Drip Tray Plate should not be placed in the dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth and rinsed thoroughly.

fig. 17	2. Cleaning the Funnel —The Funnel can be
	removed from the K-Cup®Pack Holder by
	pulling on it until it snaps off (fig. 17). The Funnel
	is dishwasher safe. To replace it, just snap it
	back onto the K-Cup®Pack Holder Assembly.
	3. Cleaning the Exit Needle —The Exit Needle is
!	located on the inside bottom of the K-Cup®Pack
	Holder Assembly. Should a clog arise due to
	coffee grinds, it can be cleaned using a paper
	clip or similar tool. Remove K-Cup®Pack Holder
	Assembly and detach Funnel. Insert the paper
	clip (fig. 17) into the Exit Needle to loosen the
	clog and push it out. The K-Cup®Pack Holder is
	dishwasher safe. CAUTION: There are sharp
needles that puncture the K-Cup®pack above the K-Cup®Pack Holder and in

the bottom of the K-Cup®Pack Holder. To avoid risk of injury, do not put your fingers in the K-Cup®Pack Assembly Housing.

1.Rinse the filter screen with the strong force of water from your faucet.

2.If you have a sprayer, aim the water spray at the filter screen.

3.Fill the Water Reservoir with approximately two inches of clean water and agitate (shake) the Water Reservoir.

Empty the Water Reservoir then fill it with clean water and return it to the Brewer. If needed, repeat above procedures. CAUTION: Please rinse the Water Reservoir thoroughly after cleaning. This will ensure that no cleaners or cleaning solutions remain as they may contaminate the water supply in the Brewer.

De-Scaling Your Brewer

Mineral content in water varies from place to place. Depending on the mineral content of the water in your area, calcium deposits or scale may build up in your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer performance. De-scaling your Brewer helps maintain the heating element and other internal parts of the Brewer that come in contact with water.

temperature one degree at a time.

Cleaning the K-Cup®Pack Holder Assembly

The Brewer should be de-scaled every 3-6 months

fig. 15

CLOCK

AUTO OFF

ON OFF TIME

SET BREW TEMP

192°

MENU

4.Once you have reached your desired brew temperature, press the Menu Button once to exit the programming mode. “BREW TEMP SET” will be indicated in the LCD Control Center if you have changed it from 192°.

5.To change the brew temperature again, repeat steps 1 through 3 to change the temperature up or down, remembering that the temperature can only be between 187° and 192°.

fig. 16	1. Cleaning the Parts —TheK-Cup®Pack Holder
	Assembly can be placed onto the top shelf of a
	dishwasher. NOTE: Use low temperature cycles
	in the dishwasher. To remove from the Brewer,
	open the cover by lifting the Handle. Grasp the
	top of the K-Cup®Pack Holder with one hand
	while pushing up on the bottom of the K-Cup®
	Pack Holder from underneath with the other
	until it releases (fig. 16). After cleaning, align the
	K-Cup®Pack Holder with the opening using the
	two front ribs as a guide, and snap into place
	from the top.

Cleaning the Water Reservoir & Water Reservoir Lid

The Water Reservoir Lid and Water Reservoir should be periodically inspected and cleaned.

The Water Reservoir Lid or Water Reservoir should not be put into the dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth and rinsed thoroughly. Do not dry the inside of the Water Reservoir with a cloth as lint may remain.

To clean the filter screen at the base of your Water Reservoir, empty the Water Reservoir and follow one or all of the following procedures.

NOTE: If you are using a water filter inside the Water Reservoir, remove it before cleaning.

fig. 18

DE-SCALE 11:56AM

MENU

to ensure optimal performance. It is possible for calcium deposits to build up faster, making it necessary to de-scale more often.

You should promptly de-scale if “DE-SCALE” is indicated on the LCD Control Center (fig. 18). However, even if “DE-SCALE” is not indicated, you should continue to de-scale your Brewer every 3-6 months. Properly follow the de-scaling procedure described on page 14.

12

13