SRS Labs Lock-In Amplifier Analog Output and Control, Expand, Front Panel, Microprocessor Control

Page 40

U419. Analog switch U418 selects the time constant and gain. The full scale output of U418 is 5 volts.

The quadrature demodulator and low pass amplifiers are identical to that described above. The quadrature detector output is provided by U1119.

Analog Output and Control

The dc output of the demodulator/low pass amplifiers is passed to the reference input of multiplying DAC U502. The DAC is programmed with the appropriate attenuation to calibrate the overall gain of the lock-in. Every gain setting in each dynamic reserve is calibrated independently and the proper attenuations are stored in the unit's ROM.

The quadrature output is calibrated by DAC U1201. Amplifiers U1204 and U1205 buffer the two demodulator outputs to drive the X and Y BNC's.

A/D's

Analog multiplexer U504 selects the signal to be digitized by the microprocessor. This signal can be either the lock-in's in-phase or quadrature output or one of the four independent analog inputs buffered by U501. These general purpose inputs are located on the rear panel of the instrument. The selected signal is sampled and held on capacitor C502 and buffered by 4/4 U508. The A/D conversion is done by successive approximation using comparator

U514 to compare the sampled and held signal with known outputs of U505, a 12 bit DAC with a precision reference. Note that the output of U506, an 8 bit DAC is summed with the output of U505. This 8 bit DAC corrects for offset errors which can accumulate as analog voltages pass through buffers, S/H amps, and comparators. These offsets are measured after each unit is manufactured, and values to compensate for these offsets are placed in the unit's ROM. The polarity of the offset-corrected 12 bit DAC is set by 2/4 U511 and the SIGN bit yielding 13 bits of resolution from -10.24 to +10.24 volts.

D/A's

In addition to providing reference voltages for A/D conversion, the DAC output voltage may be multiplexed by U507 to one of eight sample and hold amplifiers which provide analog output and control voltages. The microprocessor refreshes each S/H amplifier every few milliseconds to prevent droop. Two of these outputs are available as general programmable outputs on the rear panel. Two are

used to program the band pass filter and the reference oscillator phase shift. One output is subtracted from the lock-in output in U508 to provide a variable offset and another is the rms noise output. The remaining two outputs generate the magnitude and phase output voltages.

Expand

3/4 U511 and 4/4 U1202 are the expand amplifiers. They provide a selectable gain of 10 to the channel 1 and 2 outputs just before the output buffers.

Front Panel

There are 71 led's on the front panel controlled by 9 serial-in, parallel-out shift registers. 8 of the shift registers are written to simultaneously and the 9th is written separately. 8 consecutive write operations are required to set the LED's in each case. The liquid crystal displays are managed by the display controllers, U6101, U6102, and U6103. Exclusive-or gates U6104, U6105 and U6106 drive the left over segments. Latches U6107 and U6108 provide the logic bits for these extra segments as well as the keyboard row strobes. U6109 reads the switch closures as the rows are scanned.

Microprocessor Control

The microprocessor, U701, is a Z80A CPU clocked at 4 MHz. 16K bytes of firmware are stored in the ROM, U702. U703 is a 2K byte static RAM, backed-up by a lithium battery. A power-down standby circuit, Q701, preserves the RAM contents when the power is turned off. The battery has a life of 5-10 years. The CPU has power-up and power-down resets to prevent erroneous execution during turn-on or short sags in the line voltage.

U704 is a 3-channel counter. One channel generates the baud rate for the RS232 interface while the other two are used to measure the frequency or period of the reference oscillator. U709 provides a gate pulse to counter 0. Multiplexer U708 selects whether the gate is a single period of the reference (period measurement) or a gate of known duration (frequency measurement). Counter 1 is a programmable divide by N counter whose output is either counted for one period of the reference,

36

Image 40
Contents Model SR530 Page Table of Contents Appendix C Gpib Operating NON-OPERATINGPage SR530 Specification Summary Demodulator GpibFront Panel Summary Enbw Abridged Command List Configuration Switches Status Byte DefinitionSignal Inputs Signal FiltersSR510 Guide to Operation Front Panel SensitivityDynamic Reserve StatusDisplay Select Channel 1 DisplayOutput Output ChannelRel Channel Offset ChannelRcosø Output Expand ChannelChannel 2 Display Auto Phase Reference Input Rsinø OutputTrigger Level Reference Mode Phase ControlsReference Display Time ConstantDefaults PowerLocal and Remote SR530 Guide to Operation Rear Panel Page Command Syntax SR530 Guide to ProgrammingCommunicating with the SR530 Front Panel Status LEDsRS232 Echo and No Echo Operation Try-Out with an Ascii TerminalSR530 Command List LOW Norm HighN1,n2,n3,n4 Page Status Byte ErrorsBit Reset Trouble-Shooting Interface ProblemsCommon Hardware Problems include Common Software Problems includeSR530 with the RS232 Interface SR530 with the Gpib InterfaceGpib with RS232 Echo Mode Serial Polls and Service RequestsSR530 with Both Interfaces Lock-in Technique Measurement ExampleUnderstanding the Specifications Shielding and Ground LoopsPage Page SR530 Block Diagram Signal Channel Phase Sensitive DetectorsReference Channel DC Amplifiers and System GainCircuit Description Reference Oscillator Demodulator and Low Pass AmplifierAnalog Output and Control ExpandFront Panel Microprocessor ControlRS232 Interface Power SuppliesGpib Interface Amplifier and Filter Adjustments Multiplier AdjustmentsCalibration and Repair Notch Filters Replacing the Front-End TransistorsAppendix a Noise Sources and Cures Non-Essential Noise SourcesPage Page Case 1 The Simplest Configuration Appendix B Introduction to the RS232Baud Rate Case 2 RS232 with Control LinesStop Bits ParityVoltage Levels Final TipAppendix C Introduction to the Gpib Bus DescriptionAppendix D Program Examples Program Example IBM PC, Basic, via RS232Program Example IBM PC, Microsoft Fortran v3.3, via RS232 Page Program Example IBM PC, Microsoft C v3.0, via RS232 #include stdio.hPage Program Example 4 IBM PC,Microsoft Basic, via Gpib ′INCREMENT X6 Output by 2.5 MV Program Example HP85 via Gpib Documentation Oscillator Board Parts List PC1SW1 DpdtMain Board Parts List BR1BR2 BT1SR530 Component Parts List SR530 Component Parts List 22U MIN PIN DGpib Shielded CX1FU1 CY1MPSA18 SR530 Component Parts List SR530 Component Parts List SR530 Component Parts List SR530 Component Parts List SR530 Component Parts List 4PDT SPSTX8SR513 Assy SR530 Component Parts List Z80A-CPU Static RAM, I.CTIE Anchor TranscoverMica #4 FlatFront Panel Board Parts List RED LD2 LD1LD3 Quad Board Parts List SR530 Component Parts List PC1 SR530 Component Parts List Miscellaneous Parts List SR530 Component Parts List

SR530, Lock-In Amplifier specifications

The SRS Labs Lock-In Amplifier, model SR530, is a powerful tool designed for high-precision measurements in the realm of scientific research and industrial applications. This state-of-the-art instrument excels in extracting small signals from noisy environments, making it an invaluable asset for experiments in fields such as physics, engineering, and materials science.

One of the main features of the SR530 is its ability to perform synchronous detection, which is key to improving signal-to-noise ratios. By utilizing a reference signal, the device correlates the incoming signal with the reference to effectively filter out noise, allowing for the accurate measurement of weak signals that might otherwise be obscured. This process of phase-sensitive detection is fundamental to the operation of the Lock-In Amplifier.

The SR530 offers a wide frequency range, covering from 0.1 Hz to 100 kHz. This broad frequency response allows it to handle a diverse array of signals, making it suitable for various applications including optical detection, capacitance measurements, and in many cases, voltammetry. The device is also equipped with multiple inputs and outputs, facilitating the integration with other laboratory equipment and enabling complex experimental setups.

Precision is further enhanced with its adjustable time constant, which allows users to optimize the response time based on experimental needs. The user can choose time constants from 10 microseconds to 10 seconds, accommodating fast dynamic measurements as well as those requiring stability over longer durations.

Another remarkable characteristic of the SR530 is its digital processing capabilities. The device features a highly accurate digital voltage measurement system, minimizing drift and ensuring long-term stability. Additionally, the use of microprocessors enhances data handling and allows for features such as programmable settings, facilitating automated measurements.

Moreover, the SR530 includes a range of output options, including analog outputs, which can be used for direct signal processing, as well as digital interfaces for integration with computers. This ensures that users can not only capture high-fidelity data but also analyze and display it efficiently.

In conclusion, the SRS Labs SR530 Lock-In Amplifier stands out due to its sophisticated technology, versatile features, and robust performance. Its precision, flexibility, and ease of use make it an ideal choice for researchers and engineers looking to unlock the potential of weak signal measurement in complex environments.