SRS Labs Lock-In Amplifier, SR530 manual Stop Bits, Parity, Voltage Levels, Final Tip

Page 48

baud.) The typical data string 5.1270<cr> has 7 characters, requiring 4 msec to be sent.

Stop Bits

Generally, selection of 2 stop bits will result in fewer data transmission errors.

Parity

The Parity bit provides a check against faulty data transfer. It is not commonly used in local data transmission environments. If the parity option is selected, the SR530 will transmit 8 data bits and a parity bit, however, no parity check of incoming data is done.

Voltage Levels

The RS232 uses bipolar voltage levels:

The control lines use positive logic. For example, the DCE tells the DTE that it is clear to send (CTS) by placing > +3 VDC on pin 5 of the interface. Similarly, the DTE can tell the DCE that it is not ready by placing -3 VDC on pin 20 (DTR) of the interface.

The data lines, pins 2 and 3, use negative logic. A 'zero' bit is represented by a positive voltage and a 'one' bit is represented by a negative voltage. A start bit is a positive voltage and a stop bit is a negative voltage. Data is transmitted with the least significant bit first. The

letter 'A', which has the ASCII code 41H (0100 0001), would appear as follows:

If a parity option was selected, the parity bit would be sent after the 8th data bit, but before the first stop bit.

Final Tip

When you are trying to get the RS232 to work with your computer, it is helpful to be able to 'eavesdrop' on the RS232 data lines going between the SR530 and the computer. This can be done with an ASCII RS232 terminal and the following connector:

To test the connector, place the hook clip on pin 2 of the same connector (shorting pin 2 to pin 3.) Now, when you type at the terminal keyboard, data transmitted from pin 2 is received at pin 3 and displayed on the terminal screen. To use as a debugging tool, attach the hook clip to either pin 2 or pin 3 of the RS232 cable on the SR530 to show either data sent from the Computer or the SR530. The baud rate, parity, and stop bits of the terminal must match those of the SR530 and the computer. If your terminal has a mode which will display control characters (such as carriage returns and line feeds) it is helpful to operate in that mode.

A variant of the 'eavesdropping' approach is

diagrammed below:

With this cable arrangement, the ASCII terminal can listen to the data passing in both directions. The only drawback is that the terminal will display garbled data if both devices transmit data at the same time.

44

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Model SR530 Page Table of Contents Appendix C Gpib Operating NON-OPERATINGPage SR530 Specification Summary Demodulator GpibFront Panel Summary Enbw Abridged Command List Configuration Switches Status Byte DefinitionSignal Inputs Signal FiltersSR510 Guide to Operation Front Panel SensitivityDynamic Reserve StatusDisplay Select Channel 1 DisplayOutput Output ChannelRel Channel Offset ChannelExpand Channel Rcosø OutputChannel 2 Display Auto Phase Rsinø Output Reference InputTrigger Level Reference Mode Phase ControlsReference Display Time ConstantPower DefaultsLocal and Remote SR530 Guide to Operation Rear Panel Page Command Syntax SR530 Guide to ProgrammingCommunicating with the SR530 Front Panel Status LEDsRS232 Echo and No Echo Operation Try-Out with an Ascii TerminalSR530 Command List LOW Norm HighN1,n2,n3,n4 Page Errors Status ByteBit Reset Trouble-Shooting Interface ProblemsCommon Hardware Problems include Common Software Problems includeSR530 with the RS232 Interface SR530 with the Gpib InterfaceSerial Polls and Service Requests Gpib with RS232 Echo ModeSR530 with Both Interfaces Lock-in Technique Measurement ExampleUnderstanding the Specifications Shielding and Ground LoopsPage Page SR530 Block Diagram Signal Channel Phase Sensitive DetectorsReference Channel DC Amplifiers and System GainCircuit Description Reference Oscillator Demodulator and Low Pass AmplifierAnalog Output and Control ExpandFront Panel Microprocessor ControlPower Supplies RS232 InterfaceGpib Interface Multiplier Adjustments Amplifier and Filter AdjustmentsCalibration and Repair Notch Filters Replacing the Front-End TransistorsAppendix a Noise Sources and Cures Non-Essential Noise SourcesPage Page Case 1 The Simplest Configuration Appendix B Introduction to the RS232Baud Rate Case 2 RS232 with Control LinesStop Bits ParityVoltage Levels Final TipAppendix C Introduction to the Gpib Bus DescriptionAppendix D Program Examples Program Example IBM PC, Basic, via RS232Program Example IBM PC, Microsoft Fortran v3.3, via RS232 Page Program Example IBM PC, Microsoft C v3.0, via RS232 #include stdio.hPage Program Example 4 IBM PC,Microsoft Basic, via Gpib ′INCREMENT X6 Output by 2.5 MV Program Example HP85 via Gpib Documentation Oscillator Board Parts List PC1SW1 DpdtMain Board Parts List BR1BR2 BT1SR530 Component Parts List SR530 Component Parts List 22U MIN PIN DGpib Shielded CX1CY1 FU1MPSA18 SR530 Component Parts List SR530 Component Parts List SR530 Component Parts List SR530 Component Parts List SR530 Component Parts List SPSTX8 4PDTSR513 Assy SR530 Component Parts List Z80A-CPU Static RAM, I.CTIE Anchor TranscoverMica #4 FlatFront Panel Board Parts List RED LD1 LD2LD3 Quad Board Parts List SR530 Component Parts List PC1 SR530 Component Parts List Miscellaneous Parts List SR530 Component Parts List

SR530, Lock-In Amplifier specifications

The SRS Labs Lock-In Amplifier, model SR530, is a powerful tool designed for high-precision measurements in the realm of scientific research and industrial applications. This state-of-the-art instrument excels in extracting small signals from noisy environments, making it an invaluable asset for experiments in fields such as physics, engineering, and materials science.

One of the main features of the SR530 is its ability to perform synchronous detection, which is key to improving signal-to-noise ratios. By utilizing a reference signal, the device correlates the incoming signal with the reference to effectively filter out noise, allowing for the accurate measurement of weak signals that might otherwise be obscured. This process of phase-sensitive detection is fundamental to the operation of the Lock-In Amplifier.

The SR530 offers a wide frequency range, covering from 0.1 Hz to 100 kHz. This broad frequency response allows it to handle a diverse array of signals, making it suitable for various applications including optical detection, capacitance measurements, and in many cases, voltammetry. The device is also equipped with multiple inputs and outputs, facilitating the integration with other laboratory equipment and enabling complex experimental setups.

Precision is further enhanced with its adjustable time constant, which allows users to optimize the response time based on experimental needs. The user can choose time constants from 10 microseconds to 10 seconds, accommodating fast dynamic measurements as well as those requiring stability over longer durations.

Another remarkable characteristic of the SR530 is its digital processing capabilities. The device features a highly accurate digital voltage measurement system, minimizing drift and ensuring long-term stability. Additionally, the use of microprocessors enhances data handling and allows for features such as programmable settings, facilitating automated measurements.

Moreover, the SR530 includes a range of output options, including analog outputs, which can be used for direct signal processing, as well as digital interfaces for integration with computers. This ensures that users can not only capture high-fidelity data but also analyze and display it efficiently.

In conclusion, the SRS Labs SR530 Lock-In Amplifier stands out due to its sophisticated technology, versatile features, and robust performance. Its precision, flexibility, and ease of use make it an ideal choice for researchers and engineers looking to unlock the potential of weak signal measurement in complex environments.
Top Page Image Contents