Saeco Coffee Makers CAP001/A manual Light coffee dispensing, Dispensing coffee in jug

6.7Light coffee dispensing

This type of dispensing is performed by utilising doses of pre-ground coffee manually introduced into the machine through the pre-ground coffee slot (ref. 6, fig. 1). To the quantity thus provided manually the machine autonomously adds a small dose of ground coffee; this procedure compensates for the lesser quantity of ground cof- fee present in the pre-packaged bags and improves the organoleptic qualities of the drink dispensed.

- Briefly press (less than 1 sec.), the key twice and consecu- tively, the display will show “LIGHT COFFEE”;

-introduce through the pre-ground coffee slot (ref. 6, fig. 1), the contents of one dose of pre-ground coffee;

-press key or .

N.B.: Dispensing with pre-ground coffee is programmable only for one dose.

6.8Dispensing coffee in jug

This function allows the dispensing of more coffees (programma- ble) in a single container (such as a jug).

By pressing key 1 to 8 times, as many consecutive dispensing instances as requested, up to a maximum of 2,5 litres of coffee.

-Position the jug under the dispenser (ref. 21, fig. 1).

-Briefly press (less than 1 sec.) key for as many times as the number of instances to be dispensed.

The display will show “JUG X …” with the number of pro- grammed dispensing instances;

-press key to confirm and start the cycle;

-the machine will supply the dispensing instances programmed and the display will show the icon of a jug being filled with the number of instances already dispensed.

-having completed the dispensing, the display will show again

“READY FOR USE”;

-if the cycle has to be stopped before the preset time it will be sufficient to either press the jug key or any coffee keys.

N.B.: Once the desired quantity has been set, it must be con- firmed by pressing the button within 10 seconds, otherwise data are not saved.

N.B.: The electronic control of the machine automatically man- ages the double coffee dispensing cycle to reduce to the minimum the time taken.

Example: by programming 5 dispensing instances, the electronic control will set up dispensing for 2 double coffees plus a single one.

N.B.: Warning: after 1 jug dispensing at full dosage (approx. 2 litres) it is necessary to pause for 2 minutes to allow the machine standard conditions restoration.

English

6.9Hot water dispenser (LUXE version)

This function allows multiple (programmable) dispensing of hot water in a single container.

By pressing 1 to 8 times key as many consecutive and contin- uous dispensing instances will be obtained, up to a maximum of 1 litre of hot water in the same container.

-Position the container under spout (ref. 11, fig. 1).

-Briefly press (less than 1 sec.), multiple times, key accord- ing to the number of desired dispensing instances.

The display will show “HOT WATER X …” with the number of programmed dispensing instances;

-press key to confirm and start the cycle;

-the machine will supply the dispensing instances programmed and the display will show the icon of a container being filled with the number of instances already dispensed.

-having completed the dispensing, the display will show again

“READY FOR USE”;

N.B.: Once the desired quantity has been set, it must be con- firmed by pressing the button within 10 seconds, otherwise data are not saved.

N.B.: It is possible to dispense a programmed dose of hot water only when function “HOT WATER PROGRAMM.” is in “ON” mode (see “6.14 Menu-programmable functions”);

If instead the function is “OFF”, the dispensing must be stopped by pressing again key .

Danger of burns

Never direct the hot water jet towards body parts. Direct the pipe only by moving it through the special rubber heat pro- tector (ref. 9, fig. 1).

It is furthermore advisable to keep the spout submerged within the container.

6.10Steam dispenser (LUXE version)

Submerge the spout (ref.16, fig. 1) within the liquid to be warmed up and rotate the knob (ref. 12, fig. 1) anti-clockwise.

After having reached the desired temperature close the knob again by rotating it clockwise.

Danger of burns

Never aim the steam jet towards body parts. Direct the pipe only by moving it through its rubber heat protector (ref. 14, fig. 1).

It is advisable to keep the spout submerged within the container.

Important

After each usage always clean the traces of the heated drink from the spout with a moist cloth.

11