Quadra-Fire 7068-112 Castile & Santa Fe CE Pellet Stove Thermostat Location, Pre-Burn Check List

Page 18

R

Castile & Santa Fe CE Pellet Stove

B. Thermostat Location

The thermostat’s location will have some effect on the appliance’s operation.

When the thermostat is located close to the appliance, it may require a slightly higher temperature setting to keep the rest of the house comfortable.

If the thermostat location is in an adjacent room or on a different floor level, you will notice higher temperatures near the appliance.

C. Tools And Supplies Needed

Tools and building supplies normally required for instal- lation.

E. Pre-Burn Check List

1.

Place the appliance in a location near the

 

final installation area and follow the proce-

 

dures below:

2.

Open the appliance and remove all the parts

 

and articles packed inside the Component

 

Pack. Inspect all the parts and glass for ship-

 

ping damage. Contact your dealer if any irregu-

 

larities are noticed.

3.

All safety warnings have been read and fol-

 

lowed.

4.

This Owner’s Manual has been read.

5.

Floor protection requirements have been met.

6.

Venting is properly installed.

Reciprocating Saw

Hammer

Phillips Screwdriver

Tape Measure

Plumb Line

Level

Framing Material

Hi-temp Caulking Material

Gloves

Safety Glasses

7/16 inch Socket Wrench (or 10mm 6 pt or 11mm 6 pt socket)

Framing Square

Electric Drill & Bits

Self-Tapping Screws Outside Air Required Class L or PL Pellet Vent

May also need: Vent Support Straps

7.

The proper clearances from the appliance and

 

chimney to combustible materials have been

 

met.

8.

The masonry chimney is inspected by a profes-

 

sional and is clean, or the factory built metal

 

chimney is installed according to the manufac-

 

turer’s instructions and clearances.

9.

The chimney meets the required minimum

 

height.

10.

All labels have been removed from the glass

 

door.

D. Inspect Appliance and Components

WARNING! Risk of Fire! Damaged parts could impair safe operation. Do NOT install damaged, incomplete or substitute components.

Open the appliance and remove all the parts and articles packed inside the Component Pack. Inspect all the parts and glass for shipping damage.

Report to your dealer any parts damaged in shipment.

All labels have been removed from the glass door.

Plated surfaces have been wiped clean with a soft cloth, if applicable.

Read all the instructions before starting the installation.

Follow these instructions carefully during the installation to ensure maximum safety and benefit.

Follow pipe manufacturer instructions for installation and air clearance requirments.

11.

Plated surfaces have been wiped clean, if

 

applicable.

12.

Thermostat or remote has been installed.

13.

A power outlet is available nearby.

Page 18

7068-112

August 19, 2011

Image 18
Contents Models Hot glass will cause burnsCastile & Santa Fe CE Pellet Stove Santa FE CE Pellet StoveTable of Contents Castile & Santa Fe CE Pellet Stove Castile & Santa Fe CE Pellet Stove Appliance Certification Glass SpecificationsListing and Code Approvals Electrical RatingUser’s Guide Operating InstructionsCastile & Santa Fe CE Pellet Stove Fire Safety Combustible/Non-Combustible MaterialsFuel Material and Fuel Storage Starting Your First Fire Before Your First FireFilling the Hopper with Fuel Thermostat Calls For HeatIginition Cycles Fire CharacteristicsFeed Rate Adjustment Instructions Clear SpaceTypes of Fuel Quick Reference Maintenance ChartMaintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyCleaning Beneath Heat Exchanger Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning Ash Pan/Drawer Ash Removal from FireboxCleaning the Hopper Cleaning Heat Exchanger Chambers & Drop TubeCleaning the Exhaust Path Door Latch InspectionTask Contact your local dealer Cleaning the Top Vent Adapter Preparing Firebox for Non-Burn SeasonIncorrect Tall, Lazy Flame, Orange in Color Troubleshooting for Homeowner Frequently Asked QuestionsAppliance Location Design, Installation & Location ConsiderationsGetting Started Floor SupportPre-Burn Check List Castile & Santa Fe CE Pellet Stove Thermostat LocationTools And Supplies Needed Inspect Appliance and ComponentsDimensions and Clearances Appliance DimensionsVertical Installation Alcove InstallationCorner Installation Straight Back Against WallException for Horizontal Installations Castile & Santa Fe CE Pellet Stove Hearth Pad RequirementsRecommended Hearth Pad Requirements Venting Termination Requirements Negative Pressure, Shut-Down and Electrical Power FailureVent Information Avoiding Smoke and OdorsDraft Vent ConfigurationsNegative Pressure Minimum Vacuum Requirements 0957068-112 August 19 Castile & Santa Fe CE Pellet Stove Pellet Venting Charts Miniumum Vertical Vent for Two ElbowsVenting Systems AlcoveVertical into Existing Chimney Air Clearance to PipeConcrete Cap MasonryAlternate Masonry With AirspaceStraight Out DegreeCastile & Santa Fe CE Pellet Stove Through The Wall Appliance Set-Up Outside Air Kit Instructions Shown on Santa FEThermostat Installation Two Piece Log Set InstallationContact Information

7068-112 specifications

The Quadra-Fire 7068-112 is a high-performance gas-burning fireplace designed to bring warmth and elegance to any home. With its sleek design and advanced technology, it stands out as a preferred choice for homeowners looking for both form and function.

One of the main features of the 7068-112 is its impressive heating capacity. It can efficiently heat spaces up to 2,000 square feet, making it an excellent option for larger rooms or open-concept living areas. The unit boasts an impressive thermal efficiency rating, ensuring that consumers can enjoy a cozy fire without wasting energy.

The fireplace is equipped with a variety of user-friendly controls, allowing homeowners to easily adjust the flame and heat settings to achieve their desired ambiance. It features an adjustable flame height, allowing for customization of the fire's intensity, and a remote control option for added convenience. With these controls, users can effortlessly create a comfortable atmosphere from across the room.

Another notable characteristic of the Quadra-Fire 7068-112 is its unique combustion system. The fireplace utilizes a patented technology known as the Quadra-Fire Design, which promotes efficient heat delivery and emissions control. This system ensures that gases are burned thoroughly, resulting in reduced smoke and harmful emissions. In addition, the unit is equipped with a primary air control that helps maintain optimal burning temperatures, further enhancing efficiency.

The decorative options are also impressive with the 7068-112. It features a beautiful glass front that showcases the mesmerizing flames while offering a modern look. Homeowners can choose from an array of decorative media such as river rocks or glass beads to customize the appearance of their fireplace and complement their home decor.

In terms of installation, the 7068-112 is versatile, featuring a direct vent system that allows for flexible placement in a home. This venting method ensures that fresh air is drawn from the outside while safely venting exhaust gases outdoors, making it suitable for a variety of settings.

Overall, the Quadra-Fire 7068-112 is a stylish, efficient, and customizable heating solution that combines advanced technology with beautiful design, making it a desirable addition to any home.