Kenmore ULTRAFILTER 500 manual Where to Install the RO System, Tools and Materials Needed, Step

Page 4

- WHERE TO INSTALL THE RO SYSTEM -

The RO assembly and storage tank is designed for

installation under the sink, usually in the kitchen or

bathroom. The RO assembly mounts on a wall sur- face, or can lay on the cabinet floor next to the storage

tank. Hanger washers and wood screws are included

for cabinet wall mounting. The RO product water

faucet installs on the sink, or on the countertop next to the sink (pages 6 and 7).

Note: Tubing lengths allow for the removal of the

assembly from the hanger washers for servicing. If

tubing lengths are shortened for neater appear-

ance, it may be necessary to keep the assembly on

the hanger washers for service.

You can also locate the RO assembly and storage tank

FIG. 2 ]

sink drain p-trap

in any remote location from the faucet, observing safety guides on page 2. You do need a nearby water source and drain point (see page 17).

Water Supply: To provide supply water to the RO

system inlet use the included feed supply fitting or

install pipe fittings for tubing connection, as typical- ly shown on page 5.

Drain Point: A suitable drain point is needed for re-

ject water from the RO membrane. A floor drain,

laundry tub, standpipe, sump, etc., is preferred, as

shown in the remote locations drawing, page 17. A

sink p4rap drain adaptor is included to install where codes permit, as an optional drain point (page 6).

RO prod ucl:

\ [_water faucet

adapter

RO Assembly

- TOOLS AND MATERIALS NEEDED -

• adjustable wrench, standard pliers, and larger

adjustable jaw pliers or pipe wrench to fit sink drain

slotted and Phillips head screwdrivers

plumbers putty

electric drill and bits, if hole is needed for the RO faucet, page 6 and 7

- 6 STEPS TO INSTALL -

STEP

1: -

Install

Cold

Water Supply

fittings - page

STEP

4: -

Install

RO Assembly

- page

7

 

5

 

 

 

 

 

 

 

STEP

5: - Install

Storage

Tank,

Make Remaining Tub-

 

 

 

 

 

 

 

 

 

 

STEP

2: -

Install

Drain

Adapter

-

page 6

ing Connections

- page

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STEP

6:

- Sanitizing,

Pressure

Testing,

Purging

-

STEP

3: -

Install

Faucet

- pages

6

and

7

page

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Image 4
Contents Owners Manual Model noWarranty Safety GuidesFull Warranty Reverse Osmosis Drinking Water System As instructed on page 9 before using product waterBefore YOU Begin to Install the RO System Table of ContentsWhat Your Reverse Osmosis System will do Where to Install the RO System Steps to InstallTools and Materials Needed StepWater Supply Fitting Install Cold Water Supply FittingWater Supply Install Drain Adapter Install FaucetWithout dips, loops, low spots or kinks Prepare Mounting HoleInstall Install RO AssemblyConnect Tubing to Faucet AS Follows Tubing from RO SystemTypical Undersink Installation Install Storage TANK, Make Remaining Tubing ConnectionsConnect Drain TUBING, Faucet to SANITIZING, Pressure Testing & Purging Pressure TestingHOW Your Reverse Osmosis System Works Reverse Osmosis Water Flow Schematic Care of Your Reverse Osmosis System Prefilter and Post Filter CartridgesRO Membrane Cartridge Turn offthe water supply and open the RO faucetFlow Control Tubing ConnectionChanging CoUet and O-ring FIG AssemblyShutoff Other Troubleshooting Causecorrection Reverse Osmosis System Care GuideDimensions and Specifications Remote RO Installation storage tank not shown Remote Location for Reverse Osmosis SystemRepair Parts @ not included Sears