Kenmore ULTRAFILTER 300 625.384720 Install RO Assembly, Connect Tubing to Faucet AS Follows

Page 7

- STEP 3: INSTALL

..* SEM.LEF*UCET

1.Remove the large blue nut from the faucet threads.

2.Slide the three attached tubes and the telephone

style wire (monitored models only) through the sink

or countertop hole, aligning gasket under faucet base.

3.On the underside of the sink or countertop, screw

the nut on the faucet threads with the tubing and

wire running through the center hole of the nut. Tighten the nut so the faucet cannot move, but do not overtighten.

4.CONNECT TUBING TO FAUCET AS FOLLOWS.

a. Using the 3/8" x 1/4" tubing adaptor, connect the 1/4" blue tubing from the faucet to the 3/8" blue tubing from the RO.

FAUCET (cont.)-

[FIG6].

ASSEMBLED IN

MOUNTING HOLE

hole in sink or_ countertop

faucet & spout

/gasket

plumbers putty

/

1/4" red

Note: See pages 13 and 14 for tubing connection in- structions.

b. Using the 1/4" x 1/4" tubing adaptor, connect the 1/4" red tubing from the faucet to the 1/4" red tubing from the RO.

c. Monitored models only: Connect the telephone

style wire to the receptacle on PWA board in the RO manifold and route the wiring through holes in top

cover and manifold assembly.

318" black tubing

to drain point

telephone

style wire

\

tubing adapters-_o.,@

3/_" blue

tubing

tubing

tubing

nut

114" red tubing from RO drain

-STEP 4: INSTALL RO ASSEMBLY -

Hang the assembly on the included hanger washers, or lay on the cabinet floor, as desired.

1.Refer to FIG. 7 for wall mounting. Hold the assem- bly up to the wall surface and mark locations for the

hanger washers. Distance needed is 7.2" (approx. 7-7/32") apart.

2.Install hanger washers at least 15-1/2" up from the cabinet floor, allowing room to remove sumps from

filter heads. Wood screws are provided, or obtain

other fasteners as needed.

7

TUBING FROM

RO SYSTEM

FIG. 7 ] hoager

washer (2).

screw (2) __

7.2" (appr_ 7- 7/32")

 

15-1/2 '_

rrlirl.

up from floor

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Image 7
Contents Model no Owners ManualAs instructed on page 9 before using product water WarrantySafety Guides Full Warranty Reverse Osmosis Drinking Water SystemBefore YOU Begin to Install the RO System Table of ContentsWhat Your Reverse Osmosis System will do Step Where to Install the RO SystemSteps to Install Tools and Materials NeededWater Supply Fitting Install Cold Water Supply FittingWater Supply Prepare Mounting Hole Install Drain AdapterInstall Faucet Without dips, loops, low spots or kinksTubing from RO System InstallInstall RO Assembly Connect Tubing to Faucet AS FollowsTypical Undersink Installation Install Storage TANK, Make Remaining Tubing ConnectionsConnect Drain TUBING, Faucet to Pressure Testing SANITIZING, Pressure Testing & PurgingHOW Your Reverse Osmosis System Works Reverse Osmosis Water Flow Schematic Turn offthe water supply and open the RO faucet Care of Your Reverse Osmosis SystemPrefilter and Post Filter Cartridges RO Membrane CartridgeTubing Connection Flow ControlChanging CoUet and O-ring FIG AssemblyShutoff Reverse Osmosis System Care Guide Other Troubleshooting CausecorrectionDimensions and Specifications Remote Location for Reverse Osmosis System Remote RO Installation storage tank not shownRepair Parts @ not included Sears