Kenmore 665.1378, 665.1388 manual Cycle Status Indicators, Active Vent, Overfill Protection Float

Page 18

Lock On

Use the Lock On to prevent unintended use of the dishwasher between cycles.

When Lock On is lit, all buttons are disabled.

NOTE: The dishwasher door can be opened while the controls are locked.

To turn on the Lock

Press and hold HEATED DRY for 4 seconds. Lock On glows.

If you press any pad while your dishwasher is locked, the light flashes 3 times.

NOTE: If the Heated Dry option is selected, the light will temporarily turn off until Lock On glows.

To turn off the Lock

Press and hold HEATED DRY for 4 seconds. The light turns off.

4 Hr Delay

Select this option to run your dishwasher at a later time or during off-peak hours. You can add items to the load anytime during the delay. After adding items, press START/RESUME. Make sure the door is latched or the delay will not continue.

To delay the start

1.Press the delay button to choose the number of hours delayed.

2.Select a wash cycle and options.

3.Press START/RESUME.

The dishwasher starts the cycle in the selected number of hours.

NOTES:

To cancel the delay and cycle, press CANCEL/DRAIN.

To cancel the delay and start the cycle, press START/ RESUME.

Cycle Status Indicators

Follow the progress of your dishwasher with the Cycle Status indicators.

Clean

Clean glows when a cycle is finished. The light turns off when you press any button or close the door.

Sanitized

If you select the Sani Rinse option, Sanitized glows when the Sani Rinse cycle is finished. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted or the incoming water temperature is too low. The light turns off when you press any button or close the door.

Active Vent

The active vent reduces the filling and washing sounds from your dishwasher. The vent closes, after the cycle starts, to lock in sound. After the cycle finishes and the dishes cool for several hours, the vent opens. This keeps any water vapor from collecting on the countertop. Between cycles, the vent stays open for airflow, reducing the buildup of odors.

NOTE: There is a slight noise when the vent closes or opens. This is normal.

Overfill Protection Float

The overfill protection float (in the front right corner of the dishwasher tub) keeps the dishwasher from overfilling. It must be in place for the dishwasher to operate.

Check under the float for objects that may keep the protector from moving up or down.

18

Image 18
Contents Ultra Wash Dishwasher Table of Contents Protection AgreementsSears Maintenance Agreement Kenmore Elite Appliance WarrantyMaintenance Agreements CanadaDishwasher Safety Your safety and the safety of others are very importantBefore Using Your Dishwasher Parts and Features Ultra Wash Soil Removal System Featuring Smarttouch ControlsUsing Your New Dishwasher START-UP GuideLoading Top Rack Dishwasher LoadingLoading Suggestions Quiet operating tipsTo adjust the right-hand side Deluxe adjustable 2-position top rackTo adjust the left-hand side Utensil basketTo move a clip Loading Bottom RackNo-flip clips Turbozone wash areaLoading Silverware Basket To remove a small basket Dishwasher USEDetergent Dispenser Filling the dispenserRinse Aid Dispenser Rinse aid settingTo adjust the setting How much detergent to useDishwasher Efficiency Tips Cycle Selection ChartsTo check water temperature Additional efficiency tips Smart WashCanceling a Cycle Changing a Cycle or SettingAdding Items During a Cycle Option SelectionsCycle Status Indicators Active VentOverfill Protection Float Washing Special Items Material Dishwasher Safe?/CommentsYes Drain Air Gap CleaningDishwasher Care StoringTroubleshooting Dishes are not completely cleanDishwasher is not operating properly Dishes are damaged during a cycle Spots and stains on dishesDishes do not dry completely NoisesPage W10040740A