Kenmore 10653094300, 2260872 Reconnect wiring plug, Cold water supply, Connecting to Water Line

Page 8

4.Alignandreplacethetoplefthingeasshown(seeGraphic4). Tightenscrews.

Electrical Shock Hazard

Reconnect both ground wires.

Failure to do so can result in death or electrical shock.

Style 1

•Reconnect both ground wires.

•Reconnect wiring plug.

Your refrigerator has two front adjustable rollers -- one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

1.Move the refrigerator into its final position.

2.The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side (see Graphic 8).

3.Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator (see Graphic 8).

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

4.Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

5.Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

1.Do not remove screw 1

2.Ground wires

3.Green ground wire screw

Style 2

•Reconnect wiring plug.

1, Do not rernove screw 1

2, Wiring plug

5.Replace left hinge cover and screws.

6.Replace the refrigerator door by carefully lifting the door onto the bottom right hinge.

7.Align and replace the top right hinge as shown (see Graphic 6). Tighten screws.

8.Replace hinge cover and screws. Tighten screws.

9.Plug into agrounded 3 prong outlet.

Read all directions carefully before you begin.

IMPORTANT:

•If you turn the refrigerator on before the water line is connected, turn the ice maker OFE

•All installations must meet local plumbing code requirements.

•Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

Tools required: Flat-blade screwdriver, 7/_8in. and V2in. open-end wrenches or two adjustable wrenches, V4in. nut driver and drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a V4in. (6.35 ram) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/_8in. (4.76 ram) saddle valve which reduces water flow and clogs more easily.

Cold water supply

Connect the ice maker to a cold water line with water pressure between 36 and 120 psi. If you have questions about your water pressure, call your utility company.

Connecting to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a _f2in. to 11/4in. (1.25 cm to 3.18 cm) vertical COLD water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Side by Side Refrigerator 2260872Table of Contents Warranty Refrigerator Safety Before you throw away your old refrigerator or freezerInstallation Instructions When Moving Your RefrigeratorCleaning before use 1tiRecommended grounding method Base Grille Door Alignment Bottom Hinge Top Right HingeDisconnect wiring plug Door and Hinge ReplacementHandle Removal optional Style Door RemovalCold water supply Reconnect wiring plugConnecting to Water Line Connecting to Refrigerator ¢o, P22Refrigerator USE Rotary Controls on some modelsAdjusting Rotary Controls Ice dispenserTo dispense ice Water dispenserTo dispense water Dispenser lightNon-indicator water filter on some models Using the dispenser without the water filterChanging a base grille water filter cartridge Style 1 Behind the base grille filterAllow 24 hours to produce the first batch of ice To increase ice production rateTo remove and replace freezer shelf ice bin Style To remove and replace freezer door ice bucket StyleRefrigerator Features Crisper or Vegetable/Meat Drawer CoversHumidity Control is located on the crisper drawer Be o she/ve vaeswth o leCleaning your refrigerator To remove and replace the freezer basket or binTo remove and replace the bins Snap-on Door Rails To remove and replace the railsLower Freezer Light Beneath Ice Bin on some models Dispenser Light on some modelsUpper Freezer Light on some models If you choose to turn the refrigerator off before you leave Moving1ROUBLESHOOTING There is water in the defrost drain panMotor seems to run too much Ice maker is not producing ice or not enough iceWater dispenser will not operate properly Divider between the two compartments is warmIf Annual Preventive Maintenance Check at your request no Master Protection AgreementsMaintenance Agreements Sears Maintenance AgreementWater Filter Certifications Base grille water filter cartridges Cyst CartridgeProduct Data Sheets Application Guidelines/Water Supply ParametersYour Home

10653094300, 10653082300, 10653532300, 10653594300, 10653084300 specifications

The Kenmore 10653392300, 10653394300, and 10653384300 refrigerators have become popular choices for households in need of durable and effective cooling solutions. Each model represents a perfect blend of sophisticated design, advanced technology, and user-friendly features.

One of the standout features of these Kenmore refrigerators is their spacious capacity. With ample room for groceries and household items, they offer multiple shelves, bins, and compartments, allowing for optimal organization. The adjustable shelving accommodates larger items, making the refrigerator versatile for different storage needs.

Another significant aspect is the cooling technology used in these models. The Kenmore refrigerators utilize a high-efficiency cooling system that helps maintain a consistent temperature throughout the unit. This feature not only preserves food freshness but also minimizes energy consumption, leading to potential savings on electricity bills. The advanced refrigeration system is designed to operate quietly, ensuring a peaceful home environment.

In terms of user convenience, these refrigerators come equipped with built-in water and ice dispensers. The access to filtered water and ice at the touch of a button adds a level of luxury and practicality that many users appreciate. Additionally, some models feature adjustable temperature controls, allowing users to customize the cooling settings based on the food being stored.

The design of the Kenmore refrigerators is both stylish and functional. Available in various finishes, including stainless steel, these units easily blend into modern kitchens. The exterior is often designed to be smudge-proof, making it easier to maintain a clean appearance.

Furthermore, the 2260872 model is known for its energy-efficient design, which helps reduce the environmental footprint having been certified through energy ratings. This commitment to sustainability is increasingly significant for consumers looking for eco-friendly appliances.

Overall, the Kenmore 10653392300, 10653394300, 10653384300, and 10653084300 models are exemplary choices for those in search of reliable refrigeration solutions. Their combination of spacious interiors, advanced cooling technologies, user-friendly features, and attractive design make them valuable assets in any kitchen. With these refrigerators, Kenmore continues to uphold its reputation for quality and innovation in home appliances.
Top Page Image Contents