Kenmore 625.348242, 625.348252 Rotary Valve Service, Disassembly, Servicing the Valve, Assembly

Page 22

SECTION 5SERVICE mECH. INFORMATION

B. ROTARY VALVE SERVICE

BEFORE WORKING ON THE VALVE, TURN OFF

THE WATER SUPPLY AND DISCONNECT FROM

ELECTRICAL POWER. TO RELIEVE PRESSURE.

... THREE VALVE BYPASS: Close the inlet and open a filtered water faucet. Then close the outlet valve

and open the bypass valve.

... SEARS SPECIAL BYPASS: Slide the bypass valve

stem to bypass position. Loosen the three hex head

screws (see (A_ in drawing) toward the backside of

the valve to allow pressure water to bleed out (catch water with a rag).

DISASSEMBLY

To remove a part or group of parts, refer to the valve

drawing. A common screwdriver or nut driver, Phil-

lips screwdriver and pliers are the only tools needed

to completely disassemble.

\

flow plug (backwash

and fast rinse flow

rate control)

SERVICING THE VALVE

Inspect all o- rings, seals and gaskets for wear or de- fects.

Inspect the bottom surface of the rotor and disc for

scratches, chips or wear.

NOTE: If a replacement is needed, be sure to use the

current replacement part.

ASSEMBLY

Be sure all parts are in place and in the proper posi-

tion. Lubricate ALL o-rings, and seals with FDA ap- proved silicone grease. To install the rotor seal, first

place the seal into the valve groove, round side down (see cross section). Apply a light coating of sil- icone grease to the seal's crossing ribs. Then careful- ly center the wear strip on the seal, and push it

downward onto the seal.

Install the nozzle and venturi seal and drain seal.

Assemble two o-rings and the wave washer onto the rotor and disc. The center the rotor and disc, in the valve body, on the rotor seal.

Lower the cover onto the valve body and rotor shaft.

Then install the cover holding screws. BEFORE

TIGHTENING THE SCREWS, INSTALL THE VALVE CAM AND GEAR, THEN TURN THE RO-

TOR (CLOCKWISE ONLY) TO SERVICE POSI- TION.

5-5

rotor & disc

venturi seal

Tighten the screws using a criss-cross pattern. If a

torque wrench is available, torque to 30-40 inch pounds.

Lubricate the gear on the motor, and the valve cam

gear with Molykote grease, or other high quality gear lubricant.

Be sure to orient switch as shown, with lever toward the valve cam.

Problems, Questions? Call 1-800-426-9345 Kenmore Water Line

Image 22
Contents Manual Save this ManualR R a N T Y Sears Residential Water FilterN T E N Safety Guides Check List of ALL STEP-BY-STEP Guides to Install JilProgram the Timer SET Days to Recharge TimerProgram SET Recharge TimeSanitizing the Water Filter Recharge NOWError Code Faceplate Timer FeaturesVacation Adjustable Backwash Timer POWER-OUTAGE MemoryFilter Applications Clarifying FilterNeutralizer Filter Filtered Water SERVICE, and BackwashClarifier Filter Taste and Odor FilterNeutralizer Filter Keep the Filter from FreezingAdding Mineral Not Lose the Black Rubber Flow Plug and RetainerINSTRUCTED, to Relieve Water Pressure in the Tank Adding MINERAL... Neutralizer FilterSteps to ADD Mineral Important do not ADD Mineral IntoReplacing MINERAL... Taste & Odor Filter Steps to Remove and ADD MineralBefore YOU Call for SERVICE...HELPFUL Hints Checklist ProblemDimensions / Specifications Bypass Valves SINGLE-PLASTICTroubleshooting Face Plate TimerSwitch Valve Cycle Status Displays Nostics Manual Initiated Electronics DiagnosticAlways Make These Initial Checks First Other Service Manual Advance DiagnosticsAutomatic Electronic Diagnostics Procedure For Removing Error Code FromIpowerokayi Assembly Rotary Valve ServiceDisassembly Servicing the ValveBackwash Water Flow Through the Filter ValveRinse 419 KEY Part Description NO. Number Problems, Questions? Call 1-800-426-9345 Kenmore Water Line Sears Water Filters KEY Part NO. no DescriptionOur Home

625.348235, 625.348242, 625.348252 specifications

The Kenmore 625 series, specifically models 625.348252, 625.348242, and 625.348235, are exemplary products in the realm of home appliances, particularly focusing on water filtration systems. Designed for enhanced user convenience and health benefits, these models stand out for their innovative technologies and robust features.

One standout characteristic of the Kenmore 625 series is their advanced filtration capabilities. Each model utilizes a multi-stage filtration system that effectively reduces contaminants commonly found in tap water, such as chlorine, sediment, and heavy metals like lead. This is crucial for homeowners seeking to improve the taste and safety of their drinking water.

Additionally, these models incorporate a high flow rate, ensuring that users have access to clean water without experiencing the slow dispensing rates that can be a drawback with inferior systems. This makes it especially convenient in households with high water usage.

The design of the Kenmore 625 series is another highlight. The units are compact and aesthetically pleasing, making them suitable for various kitchen styles without taking up excessive counter space. Their user-friendly interface includes easily accessible controls and indicators that notify users when it is time to change the filter, thus promoting optimal performance and efficiency.

In terms of installation, the Kenmore 625 models are designed for easy setup, eliminating the need for complicated installations or professional assistance. Whether through a direct plumbing connection or using a standalone system, homeowners can quickly and efficiently implement these systems into their daily lives.

Durability is also a key point, as the materials used in construction are designed to withstand the test of time, ensuring longevity and reliable performance. The filters themselves are built to last, providing an extended service life that maximizes user investment.

Overall, the Kenmore 625.348252, 625.348242, and 625.348235 models are a significant advancement in home water filtration technology. With their focus on health, convenience, and ease of use, these units represent an excellent choice for consumers looking to enhance their water quality and make a positive impact on their household's health and wellness. The combination of effective filtration, user-friendly design, and durability ensures that these systems will meet the demands of modern households while providing peace of mind regarding water safety.